The Stovebolt Site Forums Threads Created By 801curt

Labor Day

Labor Day

Putting down your wrenches or time for
MORE wrenching?
Wrenching this Labor Day

Plenty of places to share.

Searching the Site - a click away

New here ??? Where to start?

Click on image for the lowdown.

====

Who's Online Now

7 members (Joe H, KEVINSKI, baldeagle, kades51, DennisM, Jon G, JW51), 45 guests, and 2 robots.

Key: Admin, Global Mod, Mod

Forum Statistics

Forums66

Topics128,004

Posts1,055,247

Members48,418

Most Online14,466
Apr 26th, 2026

Step-by-step instructions for pictures in the forums

Brad Allen's photos

AD Chevy Trucks

Pictures galore

Over 6,000 pictures

Brad Allen has an awesome collection of Chevrolet factory pictures that he has set up from film strips.

Check them out!

Lots of work on Brad's part ... pure enjoyment (and references) for you!

Big Thanks!

THANKS!

For helping keep this great
old truck web site
on the Internet for

over 30 years!

and not clogged down
with Ads!

Again, thanks!

Threads Created \| All Posts Threads Created By 801curt
Title	Forum	Post Time
'48 1.5 ton rear spring pin removal	Big Bolts	07/18/2017 4:39 AM
'48 ignition switch	The Electrical Bay	07/16/2017 2:42 AM
1948 Parking Brake Cable Lube	Driveline	07/14/2017 5:05 AM
Dewalt 20V Grease gun	The Tool Chest	07/12/2017 4:06 AM
Solar 6v battery tender/maintainer	The Tool Chest	11/30/2014 6:45 PM
DIY Zinc plating/copy CAD	The Tool Chest	10/26/2014 1:58 AM
'34 truck has SM420 trans, is it the same size as original trans?	Driveline	08/05/2014 9:42 PM
Could this hydrovac system work, on my '34?	Driveline	08/04/2014 7:55 PM
Voltage cut out on the generator, can I use on newer generator?	The Electrical Bay	07/27/2014 10:00 PM
please help identifying engine	Engine Shop	07/25/2014 9:22 PM
front axle washer '48 1.5ton part number?	Driveline	07/07/2014 5:26 PM
'48 1.5 ton brake shoe part numbers?	Driveline	06/20/2014 5:51 PM
'48 1.5ton 235ci/SM420 MPG	Big Bolts	03/24/2014 2:32 AM
How do you adjust valves while the truck is idling?	Engine Shop	03/10/2014 2:52 AM
Too Rich? '48 235 Loadmaster	Engine Shop	03/09/2014 2:38 AM
Rochester Power Piston '48 235	Engine Shop	03/03/2014 11:32 PM
Which Ammeter/volt meter are you using?	The Tool Chest	03/01/2014 4:41 PM
SM420 loud noises over 1200 rpm!	Driveline	02/07/2014 7:48 PM
Changing gear ratio '48 1.5ton Single speed rear-end	Driveline	02/02/2014 11:46 PM
'48 1.5ton rear drum is stuck	Driveline	02/02/2014 2:40 AM
Where does your ammeter needle rest, ignition off?	The Electrical Bay	01/10/2014 6:58 PM
Looking for Seat Belt diagram/instructions accessory manual?	Interiors	12/27/2013 11:20 PM
Determining which gears are in my rear end? '48 1.5ton	Driveline	12/17/2013 7:43 PM
PTO cable length, dash mount below headlight switch	Big Bolts	12/15/2013 5:25 PM
'48 6v negative charge after 800rpm	The Electrical Bay	12/13/2013 10:57 PM
'48 Gas gauge broken?	The Electrical Bay	11/24/2013 9:17 PM
'48 Loadmaster cigarette lighter and fresh air power	The Electrical Bay	11/18/2013 7:47 PM
Group 4.779 master parts catalog?	General Truck Talk	11/04/2013 5:41 PM
Parking brake rod '48 4400 Loadmaster	Big Bolts	11/03/2013 10:45 PM
Parking Brake '48 1.5ton	Driveline	11/03/2013 1:10 AM
1/2 or 3/4 ton wiring harness for 1.5ton	The Electrical Bay	10/23/2013 12:07 AM
2 IMP/rev distributer on '48 235ci 6v?	The Electrical Bay	10/12/2013 5:21 PM
6volt 6 cylinder low rev tachometer?	The Electrical Bay	10/11/2013 7:34 PM
'48 1.5ton Ammeter question	The Electrical Bay	10/04/2013 1:31 PM
new 6v heater blower switch smoking	The Electrical Bay	09/18/2013 11:04 AM
Lock, bearing adjusting nut 48 1.5ton	Driveline	09/11/2013 1:55 PM
Speedi Seal for 1.5ton rear axle	Driveline	09/06/2013 8:21 PM
'48 235 initial timing after rebuild, before start up	Engine Shop	08/27/2013 1:03 PM
Difference between 1/2 and 1 1/2ton Gas Tanks?	Big Bolts	07/28/2013 4:04 PM
Adding a filter to a parts washer	The Tool Chest	07/09/2013 12:23 PM

Page 1 of 2