The Stovebolt Site Forums All Posts Made By 38spshl

Fixing the old truck

BUSY BOLTERS
Are you one?

The Shop Area

continues to pull in the most views on the Stovebolt. In August alone there were over 22,000 views in those 13 forums.

See what you're missing.

Searching the Site - a click away

New here ??? Where to start?

Click on image for the lowdown.

====

Who's Online Now

1 members (Movingeric), 487 guests, and 1 robot.

Key: Admin, Global Mod, Mod

Forum Statistics

Forums66

Topics126,777

Posts1,039,270

Members48,100

Most Online2,175
Jul 21st, 2025

Step-by-step instructions for pictures in the forums

Threads Created \| All Posts All Posts Made By 38spshl
Title	Forum	Post Time
Re: casting # for sbc	Engine Shop	06/04/2004 9:55 PM
Re: casting # for sbc	Engine Shop	06/04/2004 6:47 AM
Re: Timing 180 degrees off	Engine Shop	12/10/2003 11:49 PM
Re: engine I.D.	Engine Shop	11/29/2003 3:14 AM
Re: Small Block Identification	Engine Shop	08/15/2003 2:21 AM
Re: Perhaps I should quit while I'm behind?	Engine Shop	03/31/2003 10:18 PM
Re: rear suspension swap	Engine Shop	03/27/2003 6:57 PM
Re: 402 into a '86 Silverado	Engine Shop	03/24/2003 9:45 PM
Re: 402 into a '86 Silverado	Engine Shop	03/19/2003 5:30 AM
The motor runs but the rad is suspect	Engine Shop	02/28/2003 4:43 AM
Re: New Wood picture	Paint and Body Shop	02/09/2003 2:38 AM
Re: Looking a gift horse in the mouth	Engine Shop	02/09/2003 2:33 AM
New Wood picture	Paint and Body Shop	02/08/2003 7:15 AM
Re: Looking a gift horse in the mouth	Engine Shop	02/08/2003 7:05 AM
Re: rear axle width	Engine Shop	01/28/2003 4:26 PM
Good Magazine article on a 48 Stovebolt	Engine Shop	01/18/2003 6:03 AM
Re: 12 Bolt Rear	Engine Shop	01/15/2003 8:27 AM
Re: Cutting Oak	Paint and Body Shop	01/14/2003 8:42 AM
Re: Cutting Oak	Paint and Body Shop	01/13/2003 4:47 PM
Cutting Oak	Paint and Body Shop	01/13/2003 7:05 AM
Re: Best Way to Bleed Brakes	Engine Shop	01/13/2003 6:56 AM
Re: 65' motor ? help	Engine Shop	01/07/2003 11:21 PM
Re: 65' motor ? help	Engine Shop	01/07/2003 11:10 PM
Re: mounting 350/400 combo on Must II	Engine Shop	12/03/2002 4:41 AM
Re: mounting 350/400 combo on Must II	Engine Shop	12/02/2002 2:56 AM
Re: Driveshaft lengths?	Engine Shop	11/29/2002 4:41 PM
Help needed with Panel wood dimensions	Paint and Body Shop	11/27/2002 5:12 AM
Re: Engine Specs	Engine Shop	11/27/2002 5:04 AM
Re: small block valve ajst.not running	Engine Shop	11/26/2002 8:25 PM
Re: 38 panel - body work	Paint and Body Shop	11/25/2002 4:21 AM
38 panel - body work	Paint and Body Shop	11/22/2002 4:15 AM
Re: Powerglide trans problem	Engine Shop	11/14/2002 2:56 AM
Re: Timing a 350	Engine Shop	10/27/2002 10:58 PM
Re: Mounting engine on Must II	Engine Shop	10/21/2002 7:53 PM
engine is finally in.	Engine Shop	10/17/2002 3:46 PM
Re: 283 or 350?	Engine Shop	09/30/2002 5:12 AM
Re: 283 or 350?	Engine Shop	09/29/2002 8:13 AM
Re: SBC Cam Numbers & Specs?	Engine Shop	09/18/2002 8:51 PM
Re: Connecting Rod Bearings	Engine Shop	08/15/2002 1:33 AM
Re: GM axle info	Engine Shop	08/10/2002 6:14 AM

Page 1 of 2