The Stovebolt Site Forums Threads Created By Craig /49 Panel

Labor Day

Labor Day

Putting down your wrenches or time for
MORE wrenching?
Wrenching this Labor Day

Plenty of places to share.

Searching the Site - a click away

New here ??? Where to start?

Click on image for the lowdown.

====

Who's Online Now

3 members (Gdads51, 1955 1 Series, Peggy M), 44 guests, and 4 robots.

Key: Admin, Global Mod, Mod

Forum Statistics

Forums66

Topics128,010

Posts1,055,251

Members48,418

Most Online14,466
Apr 26th, 2026

Step-by-step instructions for pictures in the forums

Brad Allen's photos

AD Chevy Trucks

Pictures galore

Over 6,000 pictures

Brad Allen has an awesome collection of Chevrolet factory pictures that he has set up from film strips.

Check them out!

Lots of work on Brad's part ... pure enjoyment (and references) for you!

Big Thanks!

THANKS!

For helping keep this great
old truck web site
on the Internet for

over 30 years!

and not clogged down
with Ads!

Again, thanks!

Threads Created \| All Posts Threads Created By Craig /49 Panel
Title	Forum	Post Time
Lifter wobble in the block on installing? sum thin aint right	Engine Shop	08/15/2026 8:38 PM
Any Machinists On the Forum	Driveline	04/28/2026 9:39 PM
Help On 235 cu in Hyd Lifters	Engine Shop	02/10/2026 5:22 PM
235 dampener/balancer install issue	Engine Shop	01/13/2026 6:34 PM
235 cam plate install question	Engine Shop	01/12/2026 4:52 PM
235 cam thrust bearing	Engine Shop	10/16/2025 5:53 PM
HELP With the Flywheel Number	Engine Shop	10/16/2025 5:17 PM
Little Help with Front Fender Welt Length ('49 Panel)	Panels 'N Burbs	05/31/2024 2:46 PM
1949 Chevy Barn Door Electric switch dilemma	Panels 'N Burbs	04/13/2024 2:25 PM
HELP - Clutch Issue	Panels 'N Burbs	01/05/2020 5:40 PM
Windshield trim clips and spring question	Paint and Body Shop	12/05/2019 5:37 PM
235 Rocheser Carb Base to 216 Carb Swap	Engine Shop	05/22/2019 11:50 PM
Blue Flame or Not	The HiPo Shop	03/22/2019 5:19 PM
Rear Corner rebuild help needed	Panels 'N Burbs	03/17/2019 2:18 PM
Recommendation needed for under body coating	Paint and Body Shop	04/08/2016 2:24 PM
Rochester 1bbl leaks at the Accelerator pump shaft	Engine Shop	08/06/2015 3:28 AM
235 Oil Pan Question	Engine Shop	04/27/2015 3:24 AM
How do I replace the upper steering column bearing?	General Truck Talk	03/14/2015 3:40 PM
How Much To Rebuild My 3 Speed?	Driveline	03/08/2015 4:52 PM
New Metal versus Lead any help appreciated	Paint and Body Shop	03/01/2015 5:03 PM
The Sticky Engine ID didn't work for me! Need Help with ID	Engine Shop	02/25/2015 7:43 PM
Looking For Flywheel Bolt Retainers	Engine Shop	02/14/2015 2:35 PM
Flywheel recommendations please	Engine Shop	02/09/2015 11:42 PM
Paint mixing by weight?	Paint and Body Shop	01/10/2015 8:38 PM
Is This Number Right	Engine Shop	12/03/2014 2:05 AM
How to paint EDP parts	Paint and Body Shop	11/29/2014 2:44 AM
steering column - turn signal question?	The Electrical Bay	09/07/2013 1:12 PM
Seat Riser Needed	Panels 'N Burbs	07/28/2013 11:48 AM
A couple of questions	Panels 'N Burbs	06/24/2013 8:07 AM
What to do after having a body dipped for rust removal?	Paint and Body Shop	06/21/2013 5:18 PM
Flash Rust Prevention	Paint and Body Shop	03/16/2010 7:18 PM
King Pin Thrust Bearing Help	Panels 'N Burbs	11/18/2008 6:28 PM
49 Panel Clutch/Brake Shaft Spacers Help	Panels 'N Burbs	08/26/2008 3:52 PM
Starter Application / Identification Help	The Electrical Bay	05/14/2008 1:58 PM
Shift Linkage Bellhousing Pivot Pin Help	Engine Shop	04/27/2008 6:59 PM
What primer for EDPM painted parts	Paint and Body Shop	03/31/2008 2:42 AM
What's the Original Seats for 49 Panel	Panels 'N Burbs	10/18/2006 3:53 PM
Correct Vacuum Advance for 235 chevy	Engine Shop	09/24/2006 6:48 PM