The Stovebolt Site Forums All Posts Made By shoeless

Labor Day

Labor Day

Putting down your wrenches or time for
MORE wrenching?
Wrenching this Labor Day

Plenty of places to share.

Searching the Site - a click away

New here ??? Where to start?

Click on image for the lowdown.

====

Who's Online Now

9 members (baldeagle, Jon G, 68ironhead, Stovebolt48, GMCJammer51, dt235sd, panic, JW51, 1 invisible), 52 guests, and 1 robot.

Key: Admin, Global Mod, Mod

Forum Statistics

Forums66

Topics128,004

Posts1,055,246

Members48,418

Most Online14,466
Apr 26th, 2026

Step-by-step instructions for pictures in the forums

Brad Allen's photos

AD Chevy Trucks

Pictures galore

Over 6,000 pictures

Brad Allen has an awesome collection of Chevrolet factory pictures that he has set up from film strips.

Check them out!

Lots of work on Brad's part ... pure enjoyment (and references) for you!

Big Thanks!

THANKS!

For helping keep this great
old truck web site
on the Internet for

over 30 years!

and not clogged down
with Ads!

Again, thanks!

Threads Created \| All Posts All Posts Made By shoeless
Title	Forum	Post Time
Re: Cam Choice	Engine Shop	02/28/2006 2:53 AM
Re: Heating My Carter Webers	The HiPo Shop	04/23/2005 12:43 AM
Re: manifold heat plate	Engine Shop	03/04/2005 2:36 AM
Re: "Best" carbs for 2x1 setup on 235?	Engine Shop	02/15/2005 4:35 AM
Re: "Best" carbs for 2x1 setup on 235?	Engine Shop	02/15/2005 4:27 AM
Re: oil	Engine Shop	02/13/2005 4:28 PM
Re: Question About Side Terminal On Starter Switch	The Electrical Bay	02/13/2005 4:24 PM
Re: An interesting result after 12V conversion	The Electrical Bay	02/10/2005 12:51 AM
An interesting result after 12V conversion	The Electrical Bay	02/09/2005 2:13 AM
Tailpipe Rust treatment ?	Engine Shop	01/02/2005 6:55 PM
Re: Braided Gas Line	The HiPo Shop	12/28/2004 3:30 PM
Re: AD Door Hinge Rebuild	Paint and Body Shop	12/10/2004 7:32 PM
Fender/Grill,etc. assembly	Paint and Body Shop	12/10/2004 4:12 AM
Re: 54 1/2 ton Front End Rebuild	Engine Shop	11/25/2004 3:19 AM
Re: Wiring AD heater switch	The Electrical Bay	11/22/2004 12:43 AM
Re: ignition switch----Which terminal?	The Electrical Bay	10/20/2004 12:16 AM
Re: 348 engine	Engine Shop	10/01/2004 2:59 AM
Re: Progress report	Engine Shop	09/30/2004 2:24 AM
New wiring harness checkout	The Electrical Bay	09/24/2004 2:55 AM
Re: New gas tank	Engine Shop	09/24/2004 2:46 AM
Re: Progress report	Engine Shop	09/22/2004 5:54 PM
Progress report	Engine Shop	09/19/2004 3:07 AM
Do I need an ignition/ballast resistor?	The Electrical Bay	09/05/2004 3:07 AM
Fuse block recommendations?	The Electrical Bay	08/31/2004 3:05 AM
Re: Front shock support plates	Engine Shop	07/18/2004 7:36 PM
Re: Denny	Engine Shop	07/09/2004 12:42 AM
Dumb timing question	Engine Shop	05/19/2004 3:54 AM
Re: Information	Paint and Body Shop	05/07/2004 3:57 AM
Re: tie rod and tie rod ends install	Engine Shop	05/02/2004 1:25 PM
Re: Rear Axle Seals	Engine Shop	04/23/2004 2:54 AM
Re: Flywheel housing	Engine Shop	04/23/2004 2:50 AM
Re: aftermarket grill doesn't fit?	Paint and Body Shop	04/08/2004 12:40 AM
Re: Rebuilding Wing Windows	Paint and Body Shop	04/07/2004 4:22 AM
Re: Oops, forgot to grease the new points	Engine Shop	04/07/2004 12:52 AM
Howard's M4F vs F298	The HiPo Shop	04/03/2004 12:53 AM
Re: Seat adjuster cross linkage bar	Paint and Body Shop	03/28/2004 4:06 AM
Re: Seat adjuster cross linkage bar	Interiors	03/28/2004 4:06 AM
Re: Seat adjuster cross linkage bar	Paint and Body Shop	03/26/2004 3:02 PM
Re: Seat adjuster cross linkage bar	Interiors	03/26/2004 3:02 PM
Seat adjuster cross linkage bar	Paint and Body Shop	03/26/2004 2:22 PM

Page 1 of 4