The Stovebolt Site Forums Threads Created By beltfed

Labor Day

Labor Day

Putting down your wrenches or time for
MORE wrenching?
Wrenching this Labor Day

Plenty of places to share.

Searching the Site - a click away

New here ??? Where to start?

Click on image for the lowdown.

====

Who's Online Now

8 members (Ponchogl, baldeagle, Robert Crandall, Wheelie, ShopRag, cmayna, Lugnutz, Otto Skorzeny), 39 guests, and 2 robots.

Key: Admin, Global Mod, Mod

Forum Statistics

Forums66

Topics128,006

Posts1,055,268

Members48,418

Most Online14,466
Apr 26th, 2026

Step-by-step instructions for pictures in the forums

Brad Allen's photos

AD Chevy Trucks

Pictures galore

Over 6,000 pictures

Brad Allen has an awesome collection of Chevrolet factory pictures that he has set up from film strips.

Check them out!

Lots of work on Brad's part ... pure enjoyment (and references) for you!

Big Thanks!

THANKS!

For helping keep this great
old truck web site
on the Internet for

over 30 years!

and not clogged down
with Ads!

Again, thanks!

Threads Created \| All Posts Threads Created By beltfed
Title	Forum	Post Time
Capacitor or condenser polarity?	The Electrical Bay	12/11/2019 10:45 PM
Piston compression height?	The HiPo Shop	09/16/2019 4:00 PM
How do you put freeze plugs in?	Engine Shop	08/16/2019 12:59 AM
Bushings for tranny shift rods needed	'60-'66 Trucks	07/26/2019 8:41 PM
Rochester type B adjustment question	Engine Shop	07/24/2019 7:30 PM
Alternator pulley: 2 different widths?	The Electrical Bay	07/18/2019 3:22 PM
Resistance wire, what years.	'60-'66 Trucks	07/11/2019 1:49 AM
Winter storage..gas tank m/t or full?	General Truck Talk	06/22/2019 5:17 PM
Crank pilot bushing size?	'60-'66 Trucks	06/19/2019 1:50 AM
Battery overcharge symptoms?	The Electrical Bay	06/03/2019 1:17 AM
Where to put fuel filter?	Engine Shop	05/22/2019 2:56 PM
Fuel in fuel bowl height?	Engine Shop	03/11/2019 9:20 AM
Carb alum. plug blowout.	Engine Shop	02/27/2019 12:30 AM
Way to test auto x-mission?	Driveline	02/17/2019 3:33 PM
Loctite RTV won’t set up on intake	Engine Shop	02/15/2019 12:14 AM
Pushrod hydraulic lifter question.	Engine Shop	02/03/2019 1:49 AM
Air filter CFM question	Engine Shop	01/29/2019 8:05 PM
Radiator/heater original clamps	'60-'66 Trucks	01/29/2019 7:24 PM
230 c.i. Motor id	Engine Shop	12/27/2018 5:37 PM
Compression test-out of truck	Engine Shop	12/23/2018 3:26 PM
Front axle bearing seal, 1957 Bel Air	Driveline	12/12/2018 7:29 PM
Your thoughts on the 283c.i. Engine?	Engine Shop	12/08/2018 4:32 PM
Power Pack definition.	The HiPo Shop	10/09/2018 2:16 PM
Alternator question...long post.	The Electrical Bay	10/01/2018 4:11 PM
Where do you find information on ...?	The Electrical Bay	08/30/2018 10:17 PM
Hot starter a no go	The Electrical Bay	05/06/2018 1:49 AM
Vibrator (chopper) max current?	The Radio Bench	04/09/2018 10:34 PM
Battery with three posts. What the heck?	The Electrical Bay	02/01/2018 1:15 AM
Weak if any spark and stumped as to why.	The Electrical Bay	06/09/2017 2:56 AM
Running symptoms for non vented gas cap....more?	Engine Shop	02/28/2017 3:13 AM
1964 C10 gas tank...is it vented?	Engine Shop	02/27/2017 12:38 AM
Someone explain "lift loss" on hydraulic lifters	Engine Shop	01/03/2017 1:52 PM
Rumble off throttle going downhill mostly	Engine Shop	11/07/2016 3:33 AM
Easy identification of 235 vs. 230 engine	Engine Shop	10/31/2016 3:06 PM
1964 1/2 ton basic model wiper speeds.	'60-'66 Trucks	09/11/2016 12:47 PM
Heads up on truck with heater speed switch and heat control.	'60-'66 Trucks	09/04/2016 3:20 AM
Pertronix installed, do a mess with timing, etc.?	The HiPo Shop	08/28/2016 1:29 PM
Toyota steering box...will it fit?	'60-'66 Trucks	08/20/2016 3:50 PM
1964 C10 230ci pickup fuel filter location?	'60-'66 Trucks	08/11/2016 11:33 PM
Rumble exhaust....rich or lean?	Engine Shop	08/10/2016 11:25 PM

Page 1 of 6