The Stovebolt Site Forums All Posts Made By Wisner955

Fixing the old truck

BUSY BOLTERS
Are you one?

The Shop Area

continues to pull in the most views on the Stovebolt. In August alone there were over 22,000 views in those 13 forums.

See what you're missing.

Searching the Site - a click away

New here ??? Where to start?

Click on image for the lowdown.

====

Who's Online Now

5 members (moparguy, Otto Skorzeny, Wally / Montana, mick53, Flatlander), 575 guests, and 1 robot.

Key: Admin, Global Mod, Mod

Forum Statistics

Forums66

Topics126,776

Posts1,039,259

Members48,100

Most Online2,175
Jul 21st, 2025

Step-by-step instructions for pictures in the forums

Threads Created \| All Posts All Posts Made By Wisner955
Title	Forum	Post Time
Re: Announcing details of the Midwestern Bolters Assn Fall Roundup - 9.15-16	News and Announcements	09/13/2023 12:48 AM
Re: Throttle Rod Linkage '59 Rochester 1B Carburetor	Engine Shop	04/24/2020 6:38 PM
Re: TIMING DEGREES BTDC 1955 235	Engine Shop	02/07/2019 12:05 AM
Re: TIMING DEGREES BTDC 1955 235	Engine Shop	02/03/2019 1:46 AM
Re: vacuum advance.	Engine Shop	02/03/2019 1:11 AM
Re: apache 5.3 swap	The HiPo Shop	11/17/2017 5:27 PM
Re: 235 harmonic/crank pulley for narrow V Belt	Engine Shop	09/13/2015 10:36 PM
Re: Oxygen Sensors and Stovebolts	Engine Shop	07/29/2015 5:19 PM
Re: No signs of bed angle welds on bed	Paint and Body Shop	07/10/2013 8:16 PM
Re: Premier Street Rods cab	Paint and Body Shop	04/02/2012 5:43 PM
Re: 3-speed transmission rear mount pad	Driveline	02/09/2012 4:41 PM
Re: how to deconstruct a bed - 1953	Making a Stovebolt Bed	12/22/2011 10:24 PM
Re: Front engine mount bolts for 235 swap?	Engine Shop	10/18/2011 10:52 PM
Re: Trans mount bushing install	Engine Shop	07/03/2011 1:24 AM
Re: Bed side rail angle heighth	The HiPo Shop	03/07/2011 12:57 AM
Re: Mount at rear of Transmission?	Driveline	01/13/2011 5:33 PM
Re: 235 Hydraulic Lifters - Source?	Engine Shop	11/30/2010 6:55 PM
Re: Road Trip!	Welcome Centre	10/18/2010 12:42 AM
Re: Worn rear outer axle bearings	Engine Shop	06/16/2009 6:04 PM
Re: carb question	Engine Shop	06/10/2009 1:40 AM
Re: phos acid, how should it look when done	Paint and Body Shop	06/10/2009 1:37 AM
Re: who wants there gauges done?	The Electrical Bay	02/18/2009 8:10 PM
Re: 6 volt regulator for 12 volt syatem.	The Radio Bench	02/06/2009 4:34 PM
Re: Mounting Clifford intake/exhaust	The HiPo Shop	12/17/2008 6:58 PM
Another HEI conversion	The Electrical Bay	12/08/2008 7:00 PM
Re: Combination Punch & Flange Tool - What size ?	Paint and Body Shop	10/02/2008 4:25 PM
Re: Making some progress on brakes	Big Bolts	07/18/2008 8:38 PM
Re: welding cowl panels	Paint and Body Shop	06/26/2008 3:13 AM
Re: Motor Test Fit	Engine Shop	05/30/2008 4:05 AM
Re: Ahhh, Progress!	Big Bolts	05/19/2008 2:39 AM
Re: Re-jetting carb for Clifford Intake-235 chevy	Engine Shop	04/15/2008 9:08 PM
Re: Re-jetting carb for Clifford Intake-235 chevy	Engine Shop	04/05/2008 5:28 PM
Re: Re-jetting carb for Clifford Intake-235 chevy	Engine Shop	04/05/2008 5:18 PM
Re: best way to pull engine on 65 c60?	Big Bolts	01/24/2008 6:30 PM
Re: Cab alignment with pictures (51 half-ton)	Paint and Body Shop	11/30/2007 4:45 PM
Re: 355 rear end	Engine Shop	11/26/2007 5:17 PM
Re: Horn inop	The Electrical Bay	08/09/2007 9:50 PM
Re: need rear fenders in kansas city area for prototype	Paint and Body Shop	07/19/2007 3:29 AM
Re: Bed Angle Strip Measurements	Making a Stovebolt Bed	06/27/2007 1:55 PM
Re: Synthetic Dot 5 Brake Fluid Poll	Driveline	06/18/2007 4:39 PM

Page 1 of 5