The Stovebolt.com Forums Home | Tech Tips | Gallery | FAQ | Events | Features | Search
Brrrr

Winter is Coming
Time to think about winterizing your Bolt.
A good Tech Tip
WINTERIZING YOUR TRUCK
including a link back to the Forums for additional tips.
Searching the Site - a click away
click here to search
New here ??? Where to start?
Click on image for the lowdown. Where do I go around here?
====
Who's Online Now
4 members (Greg_H, Guitplayer, TUTS 59, dunfire), 379 guests, and 2 robots.
Key: Admin, Global Mod, Mod
Forum Statistics
Forums66
Topics128,290
Posts1,058,566
Members48,492
Most Online14,466
Apr 26th, 2026
Step-by-step instructions for pictures in the forums
Brad Allen's photos

AD Chevy Trucks

Pictures galore
Over 6,000 pictures

Brad Allen has an awesome collection of Chevrolet factory pictures that he has set up from film strips.

Check them out!

Lots of work on Brad's part ... pure enjoyment (and references) for you!

Big Thanks!

THANKS!

For helping keep this great
old truck web site
on the Internet for

over 30 years!

and not clogged down
with Ads!


Again, thanks!

Previous Thread
Next Thread
Print Thread
Joined: Aug 2011
Posts: 815
5
Shop Shark
Shop Shark
5 Offline
Joined: Aug 2011
Posts: 815
All new wiring, tight grounds, checked and double checked connections but it stays on E. And yes there is plenty of gas in the tank. My guess is the sending unit might be the culprit. Steve

Joined: Mar 2010
Posts: 10,336
5
Renaissance Man
Renaissance Man
5 Offline
Joined: Mar 2010
Posts: 10,336
Did the gauge work before?


1952 5-window - return to "as built" condition | 1950 3100 with a 235 and a T-5 transmission
Joined: Aug 2011
Posts: 815
5
Shop Shark
Shop Shark
5 Offline
Joined: Aug 2011
Posts: 815
No, it did'nt.

Joined: Apr 2008
Posts: 899
F
'Bolter
'Bolter
F Offline
Joined: Apr 2008
Posts: 899
Could be the float has a hole or has fallen off the sending unit. You'll have to pull it and have a look.


Ed
Joined: Mar 2002
Posts: 9,117
'Bolter
'Bolter
Joined: Mar 2002
Posts: 9,117
So if you disconnect the sender lead at the gauge, the reading should go to full. If you ground the sender connector at the gauge, it should read empty. The next step would be to disconnect the sender wire at the tank and take a reading in ohms from the connector to the ground. With a full tank it should be up near 30 ohms. If this is the case your sender wire is shorted to ground.


1951 GMC 1 Ton Flatbed -- It is finally on the road and what a great time I have driving it!
1951 1 Ton Completed


My Chevy Master 4 Door is on the Road!
Joined: Sep 2015
Posts: 3
C
New Guy
New Guy
C Offline
Joined: Sep 2015
Posts: 3
I'm just getting started on a 52 3/4 ton restoration. It all seems original. I started by bulling the fuel tank/lines due to rust. I've secured replacement tank and lines but am having trouble locating a 6 volt fuel level sending unit. Can anyone help me?

Joined: Sep 2001
Posts: 29,270
Bubba - Curmudgeon
Bubba - Curmudgeon
Joined: Sep 2001
Posts: 29,270
http://www.classicparts.com/1954-59...t-Style/productinfo/23-525/#.VftkHCBViko

The gauge must be 6v but the sending unit is not "voltage sensitive".

Joined: Aug 2011
Posts: 815
5
Shop Shark
Shop Shark
5 Offline
Joined: Aug 2011
Posts: 815
Welcome to Stovebolt cherrypie. In order to get the most responses for a question. you need to start your own post. Steve

Joined: Aug 2011
Posts: 815
5
Shop Shark
Shop Shark
5 Offline
Joined: Aug 2011
Posts: 815
Thanks for your advice. After some investigation, I discovered that on the tank sending unit the 1/4 " brass strip connected to the lead and the float has a slight bend and a crack near the top. Could this be the problem? The gauge did not work when I bought it and I followed all the instructions for the new harness bought from Classic parts. Steve

Joined: Aug 2011
Posts: 815
5
Shop Shark
Shop Shark
5 Offline
Joined: Aug 2011
Posts: 815
Tim, what does voltage sensitive mean? It looks like the original. Would you suspect the problem is the crack I mentioned? I am not getting any feed back. Steve

Joined: Jan 2010
Posts: 4,263
D
Shop Shark
Shop Shark
D Offline
Joined: Jan 2010
Posts: 4,263
The sender works on either 6 volt or 12 volt, it just gives an ohm reading.


Did you remove the sender?

Joined: Aug 2011
Posts: 815
5
Shop Shark
Shop Shark
5 Offline
Joined: Aug 2011
Posts: 815
Hi Gus. I have a 6v. The sender is in the truck right now. But it has been out before when I cleaned the tank. As I said, the thin 1/4" strip from the lead to the float is slightly cracked. Do you think that is the problem?

Joined: Jan 2010
Posts: 4,263
D
Shop Shark
Shop Shark
D Offline
Joined: Jan 2010
Posts: 4,263
Only way to know is to test it

Did you try truckernix suggestion above?
Did you get an ohm reading?

Joined: Aug 2011
Posts: 815
5
Shop Shark
Shop Shark
5 Offline
Joined: Aug 2011
Posts: 815
truckernix, a couple things I should say. the ground is attached to the cap where the sending lead is on the top of tank. The other is I do not have a ohm tester.

Joined: Sep 2001
Posts: 29,270
Bubba - Curmudgeon
Bubba - Curmudgeon
Joined: Sep 2001
Posts: 29,270
Originally Posted by 53Movinon
Hi Gus. I have a 6v. The sender is in the truck right now. But it has been out before when I cleaned the tank. As I said, the thin 1/4" strip from the lead to the float is slightly cracked. Do you think that is the problem?
Can you post a photo of "the thin 1/4" strip from the lead to the float"?

Joined: Jun 2012
Posts: 1,749
S
'Bolter
'Bolter
S Offline
Joined: Jun 2012
Posts: 1,749
Here is an Ohm meter that is cheap and works: http://www.harborfreight.com/7-function-multimeter-98025.html
6.00 dollars. Takes the guess work out.


Steve H
Joined: Jul 2015
Posts: 203
C
'Bolter
'Bolter
C Offline
Joined: Jul 2015
Posts: 203
Digging up an old thread with a question... On the sending unit... The wire on the center terminal goes back to the guage. Is there another ground wire that connects to the sending unit and if so does it connect to the center terminal or an outside screw?


1953 GMC 1-Ton Pickup with 350 and 700R4
Joined: May 2005
Posts: 8,983
B
Sir Searchalot
Sir Searchalot
B Offline
Joined: May 2005
Posts: 8,983
The sender/flange is grounded by the mounting screws. Since there is a gasket there and the straps can have pads and the filler has a rubber hose and paint and undercoating....(all insulators), it's a good idea to reinforce the ground with a wire from a sender flange screw to the cab or chassis. Grounding of the sender and/or gauge is the no.1 cause of "gauge not working". Of course the ground path back to the battery has to be good also. Do not ground the center terminal.


Right is right, even if everyone is against it, and wrong is wrong, even if everyone is for it. - William Penn
Joined: Jul 2015
Posts: 203
C
'Bolter
'Bolter
C Offline
Joined: Jul 2015
Posts: 203
Ok thanks


1953 GMC 1-Ton Pickup with 350 and 700R4
Joined: Jan 2010
Posts: 4,263
D
Shop Shark
Shop Shark
D Offline
Joined: Jan 2010
Posts: 4,263

Joined: May 2005
Posts: 8,983
B
Sir Searchalot
Sir Searchalot
B Offline
Joined: May 2005
Posts: 8,983
Nicely done! With braided wire no less. Dads50 does some of the cleanest work seen here on Stovebolt.


Right is right, even if everyone is against it, and wrong is wrong, even if everyone is for it. - William Penn

Moderated by  Jon G, Rusty Rod 

Link Copied to Clipboard
Home | FAQ | Gallery | Tech Tips | Events | Features | Search | Hoo-Ya Shop
Powered by UBB.threads™ PHP Forum Software 8.0.0