The Stovebolt Site Forums The Shop Area Engine Shop any experienced metalurgist on board?

Help is a click away!

VEHICLE
INFORMATION
KITS

at the

GM Heritage Center
All the details are here.

Searching the Site - a click away

New here ??? Where to start?

Click on image for the lowdown.

====

Who's Online Now

5 members (39Master85, Tronman, Dennys28, Bill Hanlon, 1 invisible), 67 guests, and 6 robots.

Key: Admin, Global Mod, Mod

Forum Statistics

Forums66

Topics128,180

Posts1,057,150

Members48,464

Most Online14,466
Apr 26th, 2026

Step-by-step instructions for pictures in the forums

Brad Allen's photos

AD Chevy Trucks

Pictures galore

Over 6,000 pictures

Brad Allen has an awesome collection of Chevrolet factory pictures that he has set up from film strips.

Check them out!

Lots of work on Brad's part ... pure enjoyment (and references) for you!

Big Thanks!

THANKS!

For helping keep this great
old truck web site
on the Internet for

over 30 years!

and not clogged down
with Ads!

Again, thanks!

Print Thread

any experienced metalurgist on board? #80279 07/23/2007 3:35 AM
Joined: Jul 2005 Posts: 595 WA. "THE WET SIDE!" 1 10 micron Shop Shark
10 micron Shop Shark 1 Joined: Jul 2005 Posts: 595 WA. "THE WET SIDE!"	could use some advice on heat range used for dropping AD axle (54') looks like were gonna go 2 1/2" with either a few leafs removed or reverse the spring eye. FEEDBACK PLEASE!

Entire Thread
Subject	Posted By	Posted
any experienced metalurgist on board?	10 micron	07/23/2007 3:35 AM
Re: any experienced metalurgist on board?	Grigg	07/23/2007 5:17 AM
Re: any experienced metalurgist on board?	Denny Graham	07/23/2007 3:00 PM
Re: any experienced metalurgist on board?	Builder	07/23/2007 3:11 PM
Re: any experienced metalurgist on board?	Grigg	07/23/2007 3:50 PM
Re: any experienced metalurgist on board?	Joe H	07/23/2007 3:59 PM
Re: any experienced metalurgist on board?	desertdog	07/23/2007 7:45 PM
Re: any experienced metalurgist on board?	MARTINSR	07/24/2007 1:25 AM
Re: any experienced metalurgist on board?	Denny Graham	07/24/2007 1:33 PM
Re: any experienced metalurgist on board?	Builder	07/24/2007 2:04 PM
Re: any experienced metalurgist on board?	Fast truck	07/26/2007 1:55 AM
Re: any experienced metalurgist on board?	atomarc	07/26/2007 2:25 AM
Re: any experienced metalurgist on board?	Lonnie Gallaher	07/26/2007 5:35 AM
Re: any experienced metalurgist on board?	Grigg	07/26/2007 2:04 PM
Re: any experienced metalurgist on board?	OldSub	07/26/2007 5:23 PM
Re: any experienced metalurgist on board?	Grigg	07/26/2007 8:43 PM
Re: any experienced metalurgist on board?	Eli	07/26/2007 10:24 PM
Re: any experienced metalurgist on board?	OldSub	07/27/2007 2:45 AM
Re: any experienced metalurgist on board?	OldSub	07/27/2007 2:52 AM
Re: any experienced metalurgist on board?	Denny Graham	07/27/2007 3:53 AM
Re: any experienced metalurgist on board?	10 micron	07/27/2007 7:27 AM
Re: any experienced metalurgist on board?	Rick In VA	07/28/2007 10:27 PM
Re: any experienced metalurgist on board?	Grigg	07/29/2007 1:18 AM
Re: any experienced metalurgist on board?	Weeds	07/29/2007 9:07 PM
Re: any experienced metalurgist on board?	Denny Graham	07/30/2007 2:15 AM
Re: any experienced metalurgist on board?	Weeds	07/30/2007 2:32 AM
Re: any experienced metalurgist on board?	Denny Graham	07/30/2007 3:19 AM
Re: any experienced metalurgist on board?	desertdog	07/30/2007 3:25 AM
Re: any experienced metalurgist on board?	Denny Graham	07/30/2007 12:09 PM
Re: any experienced metalurgist on board?	BIG CHEVY 3600	08/01/2007 3:00 AM
Re: any experienced metalurgist on board?	10 micron	08/04/2007 5:48 AM

Moderated by Phak1, Woogeroo

Hop To

Link Copied to Clipboard