| |
Click on image for the lowdown. 
====
| | | Forums66 Topics128,154 Posts1,056,838 Members48,456 | | Most Online14,466 Apr 26th, 2026 | | AD Chevy Trucks Over 6,000 pictures Brad Allen has an awesome collection of Chevrolet factory pictures that he has set up from film strips. Check them out!
Lots of work on Brad's part ... pure enjoyment (and references) for you!
| | THANKS!
For helping keep this great
old truck web site
on the Internet for over 30 years! and not clogged down with Ads! Again, thanks! | | | | Joined: Jun 2013 Posts: 148 Shop Shark | | Shop Shark Joined: Jun 2013 Posts: 148 | Yes the fuel does boil out of the carbs and down the intake. After some driving on a warmed up motor if you stop at a store for 20 - 30 minutes and come out to start the truck you have to give it extra throttle to keep it idling. It wont even idle on its own. You can smell the raw fuel out the exhaust. You have to keep the RPMs above 1500 for 20 to 30 seconds before it clears its throat and will idle on its own. On a 5 minute stop this wont happen. That's why I thought dropping the float level just a hair might help. I had an old MGA that did the same thing every summer. I have insulator blocks under both carbs and have built a heat shield from 2 layers of aluminum with 1/2" spacing between them. Even put fiberglass insulation in the air gap. I hope this info helps you guys. Thanks Sharon | | | |
Entire Thread
|
dropping float height in carter webers, 56 235 motor
| Sharon Danella | 02/12/2017 6:29 AM |
Re: dropping float height in carter webers, 56 235 motor
| beltfed | 02/12/2017 2:24 PM |
Re: dropping float height in carter webers, 56 235 motor
| truckernix | 02/12/2017 3:29 PM |
Re: dropping float height in carter webers, 56 235 motor
| Hotrod Lincoln | 02/12/2017 3:52 PM |
Re: dropping float height in carter webers, 56 235 motor
| Wrenchbender Ret. | 02/12/2017 6:20 PM |
Re: dropping float height in carter webers, 56 235 motor
| beltfed | 02/12/2017 10:47 PM |
Re: dropping float height in carter webers, 56 235 motor
| Sharon Danella | 02/13/2017 3:36 AM |
Re: dropping float height in carter webers, 56 235 motor
| tclederman | 02/13/2017 3:52 AM |
Re: dropping float height in carter webers, 56 235 motor
| Sharon Danella | 02/13/2017 3:54 AM |
Re: dropping float height in carter webers, 56 235 motor
| Sharon Danella | 02/13/2017 4:03 AM |
Re: dropping float height in carter webers, 56 235 motor
| Sharon Danella | 02/13/2017 4:13 AM |
Re: dropping float height in carter webers, 56 235 motor
| Joe H | 02/13/2017 5:18 PM |
Re: dropping float height in carter webers, 56 235 motor
| Sharon Danella | 02/13/2017 6:15 PM |
Re: dropping float height in carter webers, 56 235 motor
| Sharon Danella | 02/13/2017 11:09 PM |
Re: dropping float height in carter webers, 56 235 motor
| Sharon Danella | 02/13/2017 11:13 PM |
Re: dropping float height in carter webers, 56 235 motor
| tclederman | 02/13/2017 11:39 PM |
Re: dropping float height in carter webers, 56 235 motor
| beltfed | 02/14/2017 12:05 AM |
Re: dropping float height in carter webers, 56 235 motor
| Sharon Danella | 02/14/2017 12:13 AM |
Re: dropping float height in carter webers, 56 235 motor
| Justhorsenround | 02/14/2017 1:10 AM |
Re: dropping float height in carter webers, 56 235 motor
| tclederman | 02/14/2017 2:04 AM |
Re: dropping float height in carter webers, 56 235 motor
| Sharon Danella | 02/14/2017 2:50 AM |
Re: dropping float height in carter webers, 56 235 motor
| Sharon Danella | 02/14/2017 10:15 PM |
Re: dropping float height in carter webers, 56 235 motor
| carbking | 02/14/2017 10:42 PM |
Re: dropping float height in carter webers, 56 235 motor
| wolffcub | 02/15/2017 3:42 PM |
Re: dropping float height in carter webers, 56 235 motor
| wolffcub | 02/15/2017 3:45 PM |
Re: dropping float height in carter webers, 56 235 motor
| Sharon Danella | 02/15/2017 6:14 PM |
Re: dropping float height in carter webers, 56 235 motor
| wolffcub | 02/15/2017 6:21 PM |
Re: dropping float height in carter webers, 56 235 motor
| Sharon Danella | 02/15/2017 7:26 PM | |
| |
| |