The Stovebolt.com Forums Home | Tech Tips | Gallery | FAQ | Events | Features | Search
Brrrr

Winter is Coming
Time to think about winterizing your Bolt.
Stored trucks should have a high-quality security system. A good Tech Tip
WINTERIZING YOUR TRUCK
including a link back to the Forums for additional tips.
Searching the Site - a click away
click here to search
New here ??? Where to start?
Click on image for the lowdown. Where do I go around here?
====
Who's Online Now
2 members (78buckshot, cmayna), 111 guests, and 2 robots.
Key: Admin, Global Mod, Mod
Forum Statistics
Forums66
Topics128,279
Posts1,058,593
Members48,492
Most Online14,466
Apr 26th, 2026
Step-by-step instructions for pictures in the forums
Brad Allen's photos

AD Chevy Trucks

Pictures galore
Over 6,000 pictures

Brad Allen has an awesome collection of Chevrolet factory pictures that he has set up from film strips.

Check them out!

Lots of work on Brad's part ... pure enjoyment (and references) for you!

Big Thanks!

THANKS!

For helping keep this great
old truck web site
on the Internet for

over 30 years!

and not clogged down
with Ads!


Again, thanks!

Previous Thread
Next Thread
Print Thread
Joined: Dec 2022
Posts: 183
R
'Bolter
'Bolter
R Offline
Joined: Dec 2022
Posts: 183
I have taken one side of my rocker assembly apart for cleaning. All except the middle stand (the part the bolt goes through to attatch the rocker assembly to the head). It will not budge. Any recomendations?

Thank You
chris


Rock49 aka C-Rodg
work in progress
1956 Chevy 3100
261 engine
Joined: Feb 2004
Posts: 29,960
H
Kettle Custodian (pot stirrer)
Kettle Custodian (pot stirrer)
H Offline
Joined: Feb 2004
Posts: 29,960
Heat and a dead blow hammer. Inspect the bottom of the shafts for wear. It's possible to turn the shafts upside down and drill new oil holes with a solid carbide drill bit. Plug the upper holes with short pieces of round brass rod, tapered to be a snug fit in the holes with a drill press and a file.
Jerry


"It is better to be silent and be thought a fool than to speak and eliminate all doubt!" - Abraham Lincoln
Cringe and wail in fear, Eloi- - - - -we Morlocks are on the hunt!
There is nothing noble in being superior to your fellow man; true nobility is being superior to your former self. - Ernest Hemingway
Love your enemies and drive 'em nuts!
Joined: Oct 2021
Posts: 7,049
O
'Bolter
'Bolter
O Online: Content
Joined: Oct 2021
Posts: 7,049
Are you saying you can't loosen the bolt? Try tightening it slightly and then try to loosen it. Use a long breaker bar or pipe slipped over the ratchet handle. Is the head still on the engine and covered in oil or is it bone dry and sludged up?


1950 Chevrolet 3100 (Ol' Roy)

1939 Packard Standard Eight Coupe (The Phantom) | 1956 Cadillac Coupe de Ville (The Bismarck) | 1964 Ford Galaxie 500 coupe |1966 Ford Mustang (Little Red) | 1969 Pontiac GTO (The Dishpit) I 1979 Ford F-100 | 1976 Ford F-150 (Big Red) | 1995 Ford F-150 (Newt)
Joined: Feb 2019
Posts: 4,548
P
AD Addict & Tinkerer
AD Addict & Tinkerer
P Online: Content
Joined: Feb 2019
Posts: 4,548
You might try an impact hammer. I wouldn’t hit it hard (you don’t want to snap it off), but a few impacts might encourage it loose.

Last edited by Phak1; 11/16/2026 8:20 PM. Reason: Added a caution

Phil
Moderator, The Engine Shop, Interiors and Project Journals

1952 Chevrolet 3100, Three on the Tree, 4:11 torque tube
Updated to: ‘59 235 w/hydraulic lifters, 12v w/alternator, HEI, PCV and Power front Disc Brakes
Project Journals
Stovebolt Gallery Forum
Joined: Feb 2004
Posts: 29,960
H
Kettle Custodian (pot stirrer)
Kettle Custodian (pot stirrer)
H Offline
Joined: Feb 2004
Posts: 29,960
Please describe your problem a little more clearly. Is the bolt refusing to turn, or is the rocker shaft stand stuck on the shaft? Worst case scenario- - - - -use a cutoff wheel or a hacksaw to cut the head off the bolt. Then use vise grips or a stud puller to remove the rest of the bolt, after heating it.
Jerry


"It is better to be silent and be thought a fool than to speak and eliminate all doubt!" - Abraham Lincoln
Cringe and wail in fear, Eloi- - - - -we Morlocks are on the hunt!
There is nothing noble in being superior to your fellow man; true nobility is being superior to your former self. - Ernest Hemingway
Love your enemies and drive 'em nuts!
Joined: Dec 2022
Posts: 183
R
'Bolter
'Bolter
R Offline
Joined: Dec 2022
Posts: 183
Sorry about the inadequate description.
I have attatched a photo.
The rocker support is stuck on the rocker arm shaft.
I was going to run a screwdriver through one of the bolt holes on the shaft then secure the screwdriver in a vice to keep the rocker arm shaft stationary while I twist the support.
But thought I would ask for advice first.

Chris
Attachments
20261116_190840.jpg (158.98 KB, 71 downloads)

Last edited by Rock49; 11/17/2026 1:46 AM.

Rock49 aka C-Rodg
work in progress
1956 Chevy 3100
261 engine
Joined: Oct 2021
Posts: 7,049
O
'Bolter
'Bolter
O Online: Content
Joined: Oct 2021
Posts: 7,049
Soak it in a 50/50 mix of acetone and ATF to loosen it it up (better than PB blaster). Your method isn't a bad idea. Find a pipe to slip over the pylon to get better leverage. If the shaft isn't worn out and is still usable, getting the pylon off the shaft isn't a requirement to clean everything.


1950 Chevrolet 3100 (Ol' Roy)

1939 Packard Standard Eight Coupe (The Phantom) | 1956 Cadillac Coupe de Ville (The Bismarck) | 1964 Ford Galaxie 500 coupe |1966 Ford Mustang (Little Red) | 1969 Pontiac GTO (The Dishpit) I 1979 Ford F-100 | 1976 Ford F-150 (Big Red) | 1995 Ford F-150 (Newt)
Joined: Dec 2022
Posts: 183
R
'Bolter
'Bolter
R Offline
Joined: Dec 2022
Posts: 183
Thanks Otto.


Rock49 aka C-Rodg
work in progress
1956 Chevy 3100
261 engine
Joined: Feb 2004
Posts: 29,960
H
Kettle Custodian (pot stirrer)
Kettle Custodian (pot stirrer)
H Offline
Joined: Feb 2004
Posts: 29,960
Heat from a Propane torch and penetrating oil is your friend. The torch won't get anything hot enough to damage the metal, and a few taps with a dead blow mallet will get it moving. Concentrate the flame on the standoff and the hole will expand faster than the shaft.
Jerry


"It is better to be silent and be thought a fool than to speak and eliminate all doubt!" - Abraham Lincoln
Cringe and wail in fear, Eloi- - - - -we Morlocks are on the hunt!
There is nothing noble in being superior to your fellow man; true nobility is being superior to your former self. - Ernest Hemingway
Love your enemies and drive 'em nuts!
Joined: Dec 2022
Posts: 183
R
'Bolter
'Bolter
R Offline
Joined: Dec 2022
Posts: 183
Thanks Jerry.
I will do that before I use force.
Chris


Rock49 aka C-Rodg
work in progress
1956 Chevy 3100
261 engine
Joined: Jan 2014
Posts: 3,692
J
'Bolter
'Bolter
J Offline
Joined: Jan 2014
Posts: 3,692
Are you planning on reusing the shaft? (It looks like it has some wear, but might not be enough to worry about)

Lots of excellent suggestions here. It’s remarkable what a little bit of heat will do.

That said, if you are reusing the shaft, you could just opt to leave it be and clean in place.

Side note: Unless the top end was exposed to some weather or such without a valve cover….thats an odd place for one to stick. Makes me wonder if it’s some sort of petrified oily schmutz rather than corrosion.


1951 3100
Joined: Dec 2022
Posts: 183
R
'Bolter
'Bolter
R Offline
Joined: Dec 2022
Posts: 183
JW51,
There was between 1/8 and 1/4 of caked on oil when I took it off the head so it’s probably smutz. Once I get it cleaned I will inspect and see if it's reusable.

Its interesting the amount of wear on the rockers. The six I have removed so far, range from severly worn to perfectly smooth. Of course smooth doesn't mean there’s no wear. I’m guessing some of the valves were not rotating. I have read several posts on resurfacing them myself. I will attempt it on the worst one.

chris

Last edited by Phak1; 11/18/2026 12:59 PM. Reason: Spelling /grammar

Rock49 aka C-Rodg
work in progress
1956 Chevy 3100
261 engine

Moderated by  Phak1, Woogeroo 

Link Copied to Clipboard
Home | FAQ | Gallery | Tech Tips | Events | Features | Search | Hoo-Ya Shop
Powered by UBB.threads™ PHP Forum Software 8.0.0