The Stovebolt.com Forums Home | Tech Tips | Gallery | FAQ | Events | Features | Search
Fixing the old truck

BUSY BOLTERS
Are you one?

Where is it?? The Shop Area

continues to pull in the most views on the Stovebolt. In August alone there were over 22,000 views in those 13 forums.

Searching the Site - a click away
click here to search
New here ??? Where to start?
Click on image for the lowdown. Where do I go around here?
====
Who's Online Now
0 members (), 539 guests, and 1 robot.
Key: Admin, Global Mod, Mod
Forum Statistics
Forums66
Topics126,777
Posts1,039,270
Members48,100
Most Online2,175
Jul 21st, 2025
Step-by-step instructions for pictures in the forums
Previous Thread
Next Thread
Print Thread
Joined: Jul 2016
Posts: 41
5
'Bolter
'Bolter
5 Offline
Joined: Jul 2016
Posts: 41
I have a "small" leak coming from the seal around the manual lockout shaft on my overdrive unit. I have never been into a transmission and/or an overdrive unit. From reading Randy Rundle's document the overdrive unit must be removed and the seal replaced from the inside. Other than the caution regarding spilling the clutch rollers is it a major project to replace the seal or just leave the cookie sheet under it?

Bye the way, for those of you who may have not been aware, Randy Rundle, Author of "The Official Guide To THe Borg-Warner R-10 and R-11 Overdrive" and booklet owner of Fifth Avenue Antique Auto Parts, passed away in February 2020. He helped me with the setup of my overdrive wiring and I'm sure many others. He will be missed.


1959 Chevy Apache Stepside Truck
Joined: Apr 2005
Posts: 2,066
R
'Bolter
'Bolter
R Offline
Joined: Apr 2005
Posts: 2,066
It is not necessary to disassemble the rear housing to replace the seal on the R10H series overdrive. Some other OEM's yes.
To replace the seal on the OD shifter shaft: Remove the cable and move it out of the way, there is a small hole on the lower part of the block that holds the shaft, there is a tapered pin in that hole. Use a small pin punch to drive the tapered pin upwards, remove the pin. The shaft can now be removed.
The seal part number is: 6130, Seal, shift lever OD. You should be able to order the seal from Napa or a bearing supplier in your area.
Reassemble in the reverse order.
Fred

Note: Many of the publications are generic and cover a wide range of overdrive units. If the publication was published before 1955 it likely doesn't show the Muncie/R10 unit.


1956 3100 Pickup/Red/350/3sp OD/PS/Disc Brakes
1957 Bel Air Sport Coupe/Red/355/TH350/PS/Disc Brakes
2017 Silverado LT Single Cab SB/Black/5.3/6 Speed Trans
1947 Willys CJ2A w/F-Head engine
Joined: Jul 2016
Posts: 41
5
'Bolter
'Bolter
5 Offline
Joined: Jul 2016
Posts: 41
Thanks very much rfs56trk. That will save me time and not exceed my "pea" brain ability. Have a great day.


1959 Chevy Apache Stepside Truck

Moderated by  Dusty53, SWEET 

Link Copied to Clipboard
Home | FAQ | Gallery | Tech Tips | Events | Features | Search | Hoo-Ya Shop
Powered by UBB.threads™ PHP Forum Software 8.0.0
(Release build 20240826)
Responsive Width:

PHP: 8.3.11 Page Time: 0.134s Queries: 14 (0.087s) Memory: 0.6001 MB (Peak: 0.6370 MB) Data Comp: Zlib Server Time: 2025-09-22 07:34:45 UTC
Valid HTML 5 and Valid CSS