The Stovebolt.com Forums Home | Tech Tips | Gallery | FAQ | Events | Features | Search
Help is a click away!

VEHICLE
INFORMATION
KITS


at the

GM Heritage Center
All the details are here.

Searching the Site - a click away
click here to search
New here ??? Where to start?
Click on image for the lowdown. Where do I go around here?
====
Who's Online Now
4 members (Otto Skorzeny, klhansen, Shaffer's1950, Steelonsteel), 101 guests, and 2 robots.
Key: Admin, Global Mod, Mod
Forum Statistics
Forums66
Topics128,113
Posts1,056,618
Members48,450
Most Online14,466
Apr 26th, 2026
Step-by-step instructions for pictures in the forums
Brad Allen's photos

AD Chevy Trucks

Pictures galore
Over 6,000 pictures

Brad Allen has an awesome collection of Chevrolet factory pictures that he has set up from film strips.

Check them out!

Lots of work on Brad's part ... pure enjoyment (and references) for you!

Big Thanks!

THANKS!

For helping keep this great
old truck web site
on the Internet for

over 30 years!

and not clogged down
with Ads!


Again, thanks!

Previous Thread
Next Thread
Print Thread
Joined: Mar 2018
Posts: 178
C
Righty Tighty, Lefty Loosey
Righty Tighty, Lefty Loosey
C Offline
Joined: Mar 2018
Posts: 178

Hello all;

I was trying to figure out if my truck had the original engine or not. I am pretty sure the engine was replaced, but if there is someone who could confirm this, I would appreciate it.
I think the block serial number identifies it as a 1949 engine from a passenger car. The serial number is: GAA693I28 ( that is an "eye" not a "one" )
the truck is a 1946, 3100 series 1/2 ton serial number: 5DPJ7848

I am considering installing an oil filter system and was looking to see where the tie in locations would be. Looking at the oil filter instructions for 1949 I see the oil pressure take off, where the tee would be installed. I am wondering what the additional line ( see attached picture with mark ups ) is for. Is that an external oil line to a gallery of some sort, would that not be a good spot to tie into?

Thanks in advance,
Steve
Attachments
Pictures for Stovebolt engine oil question.docx (4.34 MB, 30 downloads)
Engine Pictures
SHA1: d7bcbd8594754e3b54985b30b8c6b27f31617059


1946 Chev 1/2 ton - 6V/+ground/Bias-ply original - shake/Rattle and Roll! (SOLD)
1940 Chev 1/2 ton Franken/Restomod
Joined: Feb 2004
Posts: 29,836
H
Kettle Custodian (pot stirrer)
Kettle Custodian (pot stirrer)
H Offline
Joined: Feb 2004
Posts: 29,836
The engine in your photo is either a 216 or a low-pressure 235, and the oil line you're referring to goes through the water jacket and supplies oil to the rocker arms from a fitting under the sheet metal side cover on the passenger's side of the engine. There is a roughly triangular-shaped sheet metal cover behind the exhaust pipe called an "oil distributor" that controls oil flow to that line. There should be a 1/8" NPT (pipe) plug beside the oil distributor that is the attachment point for the oil filter outlet line. Oil from the filter joins with the flow to the cylinder head after the oil distributor does its thing. The purpose for the oil distributor is to restrict oil flow to the cylinder head until pressure at the crankshaft reaches at least 15 PSI, something that happens only at highway speeds on most spray-oiler engines. Plumbing the oil filter output to the head results in at least a little oil reaching the rocker arms, especially on worn out engines with very low oil pressure.
Jerry


"It is better to be silent and be thought a fool than to speak and eliminate all doubt!" - Abraham Lincoln
Cringe and wail in fear, Eloi- - - - -we Morlocks are on the hunt!
There is nothing noble in being superior to your fellow man; true nobility is being superior to your former self. - Ernest Hemingway
Love your enemies and drive 'em nuts!
Joined: Mar 2018
Posts: 178
C
Righty Tighty, Lefty Loosey
Righty Tighty, Lefty Loosey
C Offline
Joined: Mar 2018
Posts: 178
Thank-you Lincoln for the explanation.

I think I understand it now. I just need to locate the correct filter unit.


1946 Chev 1/2 ton - 6V/+ground/Bias-ply original - shake/Rattle and Roll! (SOLD)
1940 Chev 1/2 ton Franken/Restomod

Moderated by  Phak1, Woogeroo 

Link Copied to Clipboard
Home | FAQ | Gallery | Tech Tips | Events | Features | Search | Hoo-Ya Shop
Powered by UBB.threads™ PHP Forum Software 8.0.0