Winter is Coming
Time to think about winterizing your Bolt.
A good Tech Tip WINTERIZING YOUR TRUCK including a link back to the Forums for additional tips.
I have seen some new Rochester B copied carburetors. They look just like the originals but have a bright finish. I think I know where they are coming from. Are the major truck parts vendors selling these? has anyone seen one in use?
As far as I now, none of our well known and established vendors are offering these overseas made wannabe Rochester B's.
For the most part, reading through many posts from fellow Stovebolter's that have purchased and attempted to use them (they carry numerous brand names, but likely are all made by the same company), most have reported that their performance and reliability is anywhere from mediocre to poor.
They look pretty, but they don't seem to step up to the plate IMHO.
Others will likely chime in further with their experiences.
~ Dan 1951 Chevy 3 window 3100 Follow this story in the DITY Gallery "My Grandpa Carl's Truck and How it Became Mine" 1966 Chevelle (Wife's Hot Rod) | 2013 Chevy Silverado (Current daily driver) US Army MSG Retired (1977-1998) | Com Fac Maint Lead Tech Retired (1998-2021)
The new offshore "carburetors" compete ONLY in (5) above.
Jon
Good carburetion is fuelish hot air The most expensive carburetor is the wrong one you attempt to modify. If you truly believe "one size fits all," try walking a mile in your spouse's shoes! The Carburetor Shop
In the early 1950s, the Rochester B was an attempt by GM to get away from Carter as the primary source of Chevrolet carburetors. Their goal was cost reduction. It was not intended to be an upgrade. Carter responded by marketing a direct replacement carb and vowed to sell a million of them. It took a few years, but when the 1 millionth carb came off the assembly line, Carter had it gold plated and presented it to the CEO of General Motors. My father's shop was a Carter stocking dealer for many years during the 1950s. The company had a popular slogan back then- - - -"The ABCs of carburetion- - - -Always Buy Carter!" Making a "clone" of a substandard carburetor just adds another level of stupidity to that situation! Jerry
"It is better to be silent and be thought a fool than to speak and eliminate all doubt!" - Abraham Lincoln Cringe and wail in fear, Eloi- - - - -we Morlocks are on the hunt! There is nothing noble in being superior to your fellow man; true nobility is being superior to your former self. - Ernest Hemingway Love your enemies and drive 'em nuts!
If you want an original Rochester B carb, I'm sure one of our members will sacrifice a doorstop and send one to you. I was fortunate that my truck already had a Carter YF on it, but have two Rochester B carbs in my collection of doorstops, one from a 216 and another from a later 235.
Kevin 1951 Chevy 3100 work truck Follow this saga in Project Journal Photos 1929 Ford pickup restored from the ground up. | 1929 Ford Special Coupe (First car) Busting rust since the mid-60's If you're smart enough to take it apart, you darn well better be smart enough to put it back together.
“ Thousands of them still soldier on atop Stovebolt 6’s around the world” Our Leader. It’s great we have the freedom to have our own opinions ! I only have used B’s but I’d love to try the Carter! What I’d love to see is that gold plated carburetor. Wonder if it’s in the General Motors Museum.😀
~Charley 1954 Chevy 3100 with 235 “Bud” Follow along in the DITY 1963 Chevy half ton stepside short box 230 1954 GMC 3 ton 302 And several more Chevy camper and work trucks 1979 1987 1996
In the mid-1970s I and a safety engineer inspected a carburetor rebuilding shop here in Dallas...the largest in DFW. They had suffered 2 serious fires and we needed to find out why (we insured them). I won't bore you with all details but suffice to say the two guys "rebuilding" Rochester B and B variants just took them apart and tossed the pieces on a metal cart sitting between them which was taken to a dunk pit (uncovered...which turned out to be the cause of the fires). The carburetors had been sent in from auto parts stores as exchange carbs. The parts would soak overnight in the pit and the next day would be spent re-assembling them and labeling as "professionally rebuilt" carburetors. Occasionally a lady would come by and put them in boxes.
When I asked the supervisor where all the tags were and how they kept the parts matched, he looked at me over the lit cigarette he had dangling out of his mouth and said "Hunh? Matching parts? Tags? We can't worry about that." In a wire basket on the table where a "rebuilder" was working were a bunch of misc parts including floats, idle screws, interior pieces, etc. I asked what those were for and he said "well, we do our best but sometimes the guys work so fast to make their quota they overlook things so whatever's left just goes into those small baskets in case they need it later." He laughed and said "Wouldn't make sense to start opening up rebuilt carbs to see where you forgot the float or something. Somebody out there will return it when it doesn't work."
Hopefully rebuilders in other parts of the country did a better job. If a Rochester B, BC, etc ever made it to this place there was no way in the world it was going to remain matched and original.
~ Jon 1952 1/2 ton with 1959 235 | T5 with 3.07 rear end
LOL, those guys don't know anything. You're supposed to use old coffee cans for leftover parts.
Kevin 1951 Chevy 3100 work truck Follow this saga in Project Journal Photos 1929 Ford pickup restored from the ground up. | 1929 Ford Special Coupe (First car) Busting rust since the mid-60's If you're smart enough to take it apart, you darn well better be smart enough to put it back together.
Well gee, Kevin...they told us they were "professionals." Tattoos were not all that popular back then but we could see they had several of them. Maybe they had graduated past the old coffee can days...RHIP as we used to say. The baskets were nice looking and probably newish. Small screen, maybe stainless...looked like the tops could be closed and added to the dunk tank. And it could be the old coffee cans they'd been using burned up in the two fires. Pretty much everything else did. As I recall one was a 4 alarm fire that even ruined the steel roof beams. Those tanks of whatever they soaked the carburetors in burned really hot and there were 55 gallon drums stored right next to them to enhance the safety program they didn't have.
There was a sign on a post out by the street that said "Now Hiring." It was in an outcropping of rangy weeds and looked like it had been there since the 1950s and possibly had never been taken down. A sign that might have appeared in a gloomy backwoods episode of The Twilight Zone. The inspector had a little Minox camera in his shirt pocket and was taking lots of pictures for the report he was writing. He said he'd mail me copies of them but he never did. A great inside look at professional carburetor rebuilding.
~ Jon 1952 1/2 ton with 1959 235 | T5 with 3.07 rear end
“ Thousands of them still soldier on atop Stovebolt 6’s around the world” Our Leader. It’s great we have the freedom to have our own opinions ! I only have used B’s but I’d love to try the Carter! What I’d love to see is that gold plated carburetor. Wonder if it’s in the General Motors Museum.😀
Indeed….untold thousands of B’s still in service. And I have witnessed a good many on smooth-running engines.
The B’s many shortcomings are well documented and well understood. That said, I think the low level of “fussiness” of a GM inline 6 can mask some of those shortcomings. A carb providing a somewhat consistent “controlled spill” is good enough to provide a reasonably good result. The relative lack of optimized intake and exhaust flow, strange combustion chamber, etc….lots of limitations in a Stovebolt before the carb becomes a true limitation.
I will say that the difference I witnessed on MY 235 was night and day. I thought I had it running reasonably well with the B. But the YF was just a complete transformation in smoothness of acceleration, ease of starting, idle quality, etc.
Great story, Jon. Wrong and missing parts sure wouldn’t help ! “ Somebody out there will return it when it doesn’t work” !!! And apparently this was before China. JW, thanks for the clarification on the B shortcomings. Controlled Spill, evokes quite an image. In working on old B’s , my biggest impression is the little power piston and how easy it is for it to stick with the slightest corrosion or mineral deposit. Going back to the new Rochester B copies, I’m sure I wouldn’t buy one. Charley
~Charley 1954 Chevy 3100 with 235 “Bud” Follow along in the DITY 1963 Chevy half ton stepside short box 230 1954 GMC 3 ton 302 And several more Chevy camper and work trucks 1979 1987 1996
I like Carb King's suggestion- - - - -"Hire a kid to ride on the fender and dribble gasoline out of a leaky cowboy boot into the intake manifold!" It just might improve the gas mileage and engine performance! LOL! Jerry
"It is better to be silent and be thought a fool than to speak and eliminate all doubt!" - Abraham Lincoln Cringe and wail in fear, Eloi- - - - -we Morlocks are on the hunt! There is nothing noble in being superior to your fellow man; true nobility is being superior to your former self. - Ernest Hemingway Love your enemies and drive 'em nuts!
~Charley 1954 Chevy 3100 with 235 “Bud” Follow along in the DITY 1963 Chevy half ton stepside short box 230 1954 GMC 3 ton 302 And several more Chevy camper and work trucks 1979 1987 1996
It maybe just me but I think the Rochester "B" gets a bad wrap. I have been running one on my 235 in the '58 1.5 Ton. I just completed a 500 mile round trip without a hiccup. I averaged 10.5 Mpg..
~ Craig 1958 Viking 4400 "The Book of Thor" Read the story in the DITY 1960 Chevrolet C10 "A Family Heirloom" Follow the story in the DITY Gallery '59 Apache 31, 327 V8 (0.030 over), Muncie M20 4 Speed, GM 10 Bolt Rear... long term project (30 years and counting)
If you don't like driving yourTruck, you won't drive yourTruck..| Living life in the SLOW lane
Maybe its just the difference of "good enough" versus better.
1950 Chevrolet 3100 (Ol' Roy)
1939 Packard Standard Eight Coupe (The Phantom) | 1956 Cadillac Coupe de Ville (The Bismarck) | 1964 Ford Galaxie 500 coupe |1966 Ford Mustang (Little Red) | 1969 Pontiac GTO (The Dishpit) I 1979 Ford F-100 | 1976 Ford F-150 (Big Red) | 1995 Ford F-150 (Newt)
I have nothing against the Rochester B and in fact I have had good service from the ones I have used. I started this post because I was curious if these copied ones were turning up in numbers. The GM Rochester B performed faithfully for many cars and trucks throughout the years.
My school car almost 70 years ago was a 1957 GMC and I have played with GMC ever since. I would consider rebuilding a Zenith from a GMC and putting it on a Chev before I would buy a Chinese carb. I have run Carter Y-F on GMC but I have never run a Rochester single barrel so I can't say anything good or bad about them. But I think you would be just as disappointed with a Chinese Rochester knock off as I have been with Chinese Stihl and Honda knock offs.
I have purchased stuff from Jim through the years and I have met him personally several times. He has offered stuff like reproduction GMC oil lines that go to the head that he had built. They were excellent quality and I still have a few which I stocked up on while they were available. I wonder if he had these reproductions built or if they come out of the same factory that builds the under $100 eBay carbs. If I were interested in buying one for almost $400 I would call him and talk to him. He is a very honest person.
I seriously doubt that these carbs are true reproduction Rochester Bs. Why would anyone pay big money to contract to make perfect Rochester B clones instead of perfect Carter YF clones? I'd bet money that they're the same as the ebay ones.
Unless one of Carbking's rebuild kits will work on the JC Rochester B, it's a China special.
Last edited by Phak1; 11/15/20268:00 PM. Reason: Typo
1950 Chevrolet 3100 (Ol' Roy)
1939 Packard Standard Eight Coupe (The Phantom) | 1956 Cadillac Coupe de Ville (The Bismarck) | 1964 Ford Galaxie 500 coupe |1966 Ford Mustang (Little Red) | 1969 Pontiac GTO (The Dishpit) I 1979 Ford F-100 | 1976 Ford F-150 (Big Red) | 1995 Ford F-150 (Newt)
Carbking does NOT offer any parts, kits, or technical information on the clones, now or in the future.
Jon
Good carburetion is fuelish hot air The most expensive carburetor is the wrong one you attempt to modify. If you truly believe "one size fits all," try walking a mile in your spouse's shoes! The Carburetor Shop
1939 Packard Standard Eight Coupe (The Phantom) | 1956 Cadillac Coupe de Ville (The Bismarck) | 1964 Ford Galaxie 500 coupe |1966 Ford Mustang (Little Red) | 1969 Pontiac GTO (The Dishpit) I 1979 Ford F-100 | 1976 Ford F-150 (Big Red) | 1995 Ford F-150 (Newt)
Not wishing to hyjack thread, and if the moderators feel this post should be moved / deleted, please do so.
Otto Skorzeny's question about parts availability deserves a more complete answer.
When an individual wants a carburetor rebuilding kit, they have ONE carburetor, so finding a kit should be easy ! The individual has no way of knowing how many of a given carburetor type exists. Saying "Rochester B" is not much more, if any, informative than stating, "green truck" !
We have parts bills-of-material on 137 DIFFERENT Rochester type B (B, BC, BV) carburetors for which we offer 82 DIFFERENT rebuilding kits.
It is sufficiently difficult to identify any Rochester B if the tag is missing. So if the "clone" (fake is a better word, "clone", by definition, is an exact reproduction) does not have a tag, which kit would I sell. I doubt very seriously if a bill-of-material is available, and even if it is, it would probably be for non-English part numbers, for which I would have ZERO samples or interchange.
So, we would be guessing (GUESS who is at fault if the customer gets the incorrect kit, regardless of who does the guessing).
This post is NOT a "whine" or a "complaint" (we accepted the above when we decided to manufacture carb kits); it is simply a recognition that the offshore units are, to us, totally unknown as far as parts bills-of-material.
Jon
Good carburetion is fuelish hot air The most expensive carburetor is the wrong one you attempt to modify. If you truly believe "one size fits all," try walking a mile in your spouse's shoes! The Carburetor Shop
Not wishing to hyjack thread, and if the moderators feel this post should be moved / deleted, please do so.
Otto Skorzeny's question about parts availability deserves a more complete answer.
I believe your post is relevant. Your expertise in this field is helping many ‘bolters avoid the pitfalls of an inferior carburetor produced overseas. There are many on this forum that can attest to that.
Last edited by Phak1; 11/16/202611:37 PM. Reason: Typo
Phil Moderator, The Engine Shop, Interiors and Project Journals
1952 Chevrolet 3100, Three on the Tree, 4:11 torque tube Updated to: ‘59 235 w/hydraulic lifters, 12v w/alternator, HEI, PCV and Power front Disc Brakes Project Journals Stovebolt Gallery Forum
137 different models and 82 different rebuilding kits! I believe that indicates that the new carb you buy, whether from Jim Carter, AliExpress, EBay or a swap meet probably won't be optimal for your truck. If you have the time and don't mind experimenting, I suppose it would be OK.
Right. As usual the Fitzall is a "one size, fits none" product.
1950 Chevrolet 3100 (Ol' Roy)
1939 Packard Standard Eight Coupe (The Phantom) | 1956 Cadillac Coupe de Ville (The Bismarck) | 1964 Ford Galaxie 500 coupe |1966 Ford Mustang (Little Red) | 1969 Pontiac GTO (The Dishpit) I 1979 Ford F-100 | 1976 Ford F-150 (Big Red) | 1995 Ford F-150 (Newt)
For those who wish to use an original Rochester B (or any other original carburetor for applications before 1975) USE MY WEBSITE for a reference. I started the database from which the website is produced in 1967; there are currently 95,000 plus individual applications listed.
Caviat - NOT a sales pitch, I have ZERO Rochester type B's in my inventory.
The website is indexed. Simply go to the appropriate page, and look up the original carburetor number.
Now look at different sources for a carburetor WITH the original tag (virtually ALL commercial rebuilders build carburetors to THEIR specification, and then throw away the tag (see Jon G.'s post in this thread). If you find one with an original tag, there is a better than normal chance that the parts match.
Once you have the tagged original, use the tag number to order a rebuilding kit, and search for the excellent rebuilding help that Jon G. has published on this forum.
Jon (the other Jon)
Good carburetion is fuelish hot air The most expensive carburetor is the wrong one you attempt to modify. If you truly believe "one size fits all," try walking a mile in your spouse's shoes! The Carburetor Shop
Thanks, Jon. You may recall the summer I was doing the "Rochester Project" and the numerous conversations we had. Hundreds of digital images showing I tried and tried to come up with ways to make the power piston seal better (the bores are always worn and so are the pistons) and most especially to keep the pistons from sticking in the bores (which disables the power system completely and makes the carburetor run extra rich). I tried o-rings of all types...viton, hdpe, ldpe, nylon, rubber, teflon...most of which I still have here. Every one of them failed. I tried pure silicone grease between the o-rings...which is supposed to be resistant to gasoline. And finally I came up with a scheme to use a formed aluminum piece and an o-ring to prevent gas from being sucked up in there. My final attempt before admitting it can not be done or at least it can't be done by "everyman."
You can see much of it below in various images along with an image of one of the Chinese Rochester B "copies" showing 3 (count them, 3) vacuum inlet locations for the automatic choke. A really interesting approach, I thought. Sometimes if one vacuum pipe works well, three might work better.
As for the power piston, this is truly one of the Achille's Heel problems of the carburetor and nothing I tried helped because vacuum still sucks gasoline up in the area and it still always turns to a sticky mess. I even tested gasoline and various gas additives. I could not see any way to keep the gum from disabling the thing and it all goes back to basic design combined with no more real gasoline. I tried to keep an open mind and honestly because I've been around these carburetors for over 60 years (ugh) I tried to be as optimistic as possible but I decided there is simply no comparison between these and the Carter YF...and because of cost I didn't even get into Zenith and other options.
However if the airhorn had been attached using more than 4 screws and if the power piston scheme had been located outside of the carburetor the carburetor might have worked much better. Images below...
~ Jon 1952 1/2 ton with 1959 235 | T5 with 3.07 rear end
1939 Packard Standard Eight Coupe (The Phantom) | 1956 Cadillac Coupe de Ville (The Bismarck) | 1964 Ford Galaxie 500 coupe |1966 Ford Mustang (Little Red) | 1969 Pontiac GTO (The Dishpit) I 1979 Ford F-100 | 1976 Ford F-150 (Big Red) | 1995 Ford F-150 (Newt)