The Stovebolt.com Forums Home | FAQ | Gallery | Tech Tips | Events | Features | Search
Time to gathering together!
Fall Happenings
Since we put up promos last two weeks, we have had a bunch of activity in
The Side Lot.
See what's happening with a Stovebolt Collective near you
.

THE SIDE LOT
From Coast to Coast and some International gatherings listed, too.

Next up: too many to list!

THE SIDE LOT.

Go see!

Searching the Site

Get info about how to search the entire Stovebolt site here. To do a search for just the forums, get those details in the IT Shortbus fourm.
Old Truck Calendars
Months of truck photos!
Nothing like an old truck calendar

Stovebolt Calendars

Check for details!


Who's Online Now
8 members (NJC, Garageguy6078, Shaffer's1950, Jethro in Va, D B Cooper, Pat66), 86 guests, and 3 robots.
Key: Admin, Global Mod, Mod
Forum Statistics
Forums60
Topics129,207
Posts1,047,825
Members46,222
Most Online1,229
Jan 21st, 2020
Step-by-step instructions for pictures in the forums
Previous Thread
Next Thread
Print Thread
Page 2 of 2 1 2
Joined: Jan 2014
Posts: 2,305
J
JW51 Offline OP
'Bolter
Back to my LS musings.....

There probably isn’t a simple answer to this (depends on what vehicle), but how do folks deal with swapping a modern engine/tranny into a vehicle with one with a torque tube driveline?

It’s my understanding that the torque tube itself is integral to the rear suspension in some old cars.

Joined: Apr 2005
Posts: 11,129
Grease Monkey, Moderator General Truck Talk & Greasy Spoon
They remove the entire driveline and swap/adapt to a later setup.


Martin
'62 Chevy C-10 Stepside Shortbed (Restomod in progress)
'47 Chevy 3100 5 Window (long term project)
‘65 Chevy Biscayne 4dr 230 I-6 one owner (I’m #2) “Emily”
‘39 Dodge Businessmans Coupe “Clarence”



"I fought the law and the law won" now I are a retired one!
Support those brave men/women who stand the "Thin Blue Line"! Hug a cop!
USAF 1965-1969 Weather Observation Tech (I got paid to look at the clouds)

Joined: Jul 2019
Posts: 554
B
'Bolter
I LS swapped mine with full factory driveshaft on my 3/4 ton. It had the half torque tube. Kept the truck bone stock from the transmission back. Used it like that for a while until I swapped in the borg warner OD trans then had a new shaft made up.

Joined: Jan 2014
Posts: 2,305
J
JW51 Offline OP
'Bolter
I get the rear end swap and the switch to open driveshaft. What I don’t quite understand is how much one has to re-engineer the rear suspension (think cars that have something other than a parallel leaf spring setup).

Last edited by JW51; Wed Jul 21 2021 03:02 AM.
Joined: Jul 2019
Posts: 554
B
'Bolter
Not sure about any of the cars but the truck is pretty straightforward to bolt together any combo that you want. I have a 2001 engine bolted to a 70’s v8 truck bellhousing bolted to the factory 318 3 speed column shifted trans. When I built the truck I actually put the torque tube and rear shaft in and located the motor mounts to suite the factory driveline. Then I welded up the engine mounts and was good to go.

Page 2 of 2 1 2

Moderated by  Justhorsenround, KCMongo 

Link Copied to Clipboard
Home | FAQ | Gallery | Tech Tips | Events | Features | Search | Hoo-Ya Shop
Powered by UBB.threads™ PHP Forum Software 7.7.5