The Stovebolt.com Forums Home | FAQ | Gallery | Tech Tips | Events | Features | Search
Time to gathering together!
Fall Happenings
Since we put up promos last two weeks, we have had a bunch of activity in
The Side Lot.
See what's happening with a Stovebolt Collective near you
.

THE SIDE LOT
From Coast to Coast and some International gatherings listed, too.

Next up: too many to list!

THE SIDE LOT.

Go see!

Searching the Site

Get info about how to search the entire Stovebolt site here. To do a search for just the forums, get those details in the IT Shortbus fourm.
Old Truck Calendars
Months of truck photos!
Nothing like an old truck calendar

Stovebolt Calendars

Check for details!


Who's Online Now
17 members (32vsnake, delky, 37 GC, D B Cooper, Hendog97, Gdads51), 107 guests, and 3 robots.
Key: Admin, Global Mod, Mod
Forum Statistics
Forums60
Topics129,239
Posts1,048,097
Members46,231
Most Online1,229
Jan 21st, 2020
Step-by-step instructions for pictures in the forums
Previous Thread
Next Thread
Print Thread
#1373746 Mon Aug 17 2020 11:14 AM
Joined: Aug 2020
Posts: 86
A
AwDang Offline OP
'Bolter
Is there a more modern front hub with 9/16” studs that adapts to the 49 spindle?
Bonus if it increases track width too.

Last edited by AwDang; Mon Aug 17 2020 11:43 AM.

Pat
1940’s tech was great in the 40’s
Joined: Mar 2002
Posts: 9,154
'Bolter
What is the problem with the old hubs?

Joined: Feb 2004
Posts: 25,008
H
Kettle Custodian (pot stirrer)
It would probably be possible to adapt a later model spindle to the existing kingpin mounts. We used to install a 3/4 ton Ford rear axle load tube to the right front hub and run a "wide 5" front wheel and brake on the dirt track cars. A good machinist and welder could probably do something similar with a 3600 steering knuckle assembly. I'd probably cut off the existing spindle, bore a hole in the steering knuckle, and fabricate an appropriate-sized spindle from bar stock and press and weld it into place. Another method would be to turn the existing spindle down to a straight contour and press a fabricated spindle over it, then make a weld back at the steering knuckle. Difficult, but not impossible!
Jerry


"Freedom's just another word for nothing left to lose"
Kris Kristofferson

Cringe and wail in fear, Eloi- - - - -we Morlocks are on the hunt!

There is nothing noble in being superior to your fellow man; true nobility is being superior to your former self.
Ernest Hemingway

WAG MORE- - - - - -BARK LESS!
Joined: Aug 2020
Posts: 86
A
AwDang Offline OP
'Bolter
Originally Posted by Hotrod Lincoln
It would probably be possible to adapt a later model spindle to the existing kingpin mounts. We used to install a 3/4 ton Ford rear axle load tube to the right front hub and run a "wide 5" front wheel and brake on the dirt track cars. A good machinist and welder could probably do something similar with a 3600 steering knuckle assembly. I'd probably cut off the existing spindle, bore a hole in the steering knuckle, and fabricate an appropriate-sized spindle from bar stock and press and weld it into place. Another method would be to turn the existing spindle down to a straight contour and press a fabricated spindle over it, then make a weld back at the steering knuckle. Difficult, but not impossible!
Jerry

It would be easier just to turn some custom hubs.....


Pat
1940’s tech was great in the 40’s
Joined: Nov 2005
Posts: 6,097
3
3B Offline
'Bolter
Hy AwDang, Is your truck currently the single wheel version? If it is the single wheel version, you could swap dual wheel hubs onto the front, that would increase your track dramatically, maybe even too much.

3B #1373853 Mon Aug 17 2020 11:27 PM
Joined: Aug 2020
Posts: 86
A
AwDang Offline OP
'Bolter
Originally Posted by 3B
Hy AwDang, Is your truck currently the single wheel version? If it is the single wheel version, you could swap dual wheel hubs onto the front, that would increase your track dramatically, maybe even too much.

Hum....gotta look into that. 3800 dually front hubs?


Pat
1940’s tech was great in the 40’s

Moderated by  SWEET 

Link Copied to Clipboard
Home | FAQ | Gallery | Tech Tips | Events | Features | Search | Hoo-Ya Shop
Powered by UBB.threads™ PHP Forum Software 7.7.5