The Stovebolt.com Forums Home | FAQ | Gallery | Tech Tips | Events | Features | Search
Time to gathering together!
Fall Happenings
Since we put up promos last two weeks, we have had a bunch of activity in
The Side Lot.
See what's happening with a Stovebolt Collective near you
.

THE SIDE LOT
From Coast to Coast and some International gatherings listed, too.

Next up: too many to list!

THE SIDE LOT.

Go see!

Searching the Site

Get info about how to search the entire Stovebolt site here. To do a search for just the forums, get those details in the IT Shortbus fourm.
Old Truck Calendars
Months of truck photos!
Nothing like an old truck calendar

Stovebolt Calendars

Check for details!


Who's Online Now
0 members (), 80 guests, and 3 robots.
Key: Admin, Global Mod, Mod
Forum Statistics
Forums60
Topics129,207
Posts1,047,820
Members46,222
Most Online1,229
Jan 21st, 2020
Step-by-step instructions for pictures in the forums
Previous Thread
Next Thread
Print Thread
Page 1 of 2 1 2
Joined: Oct 2019
Posts: 32
D
'Bolter
I got a 1st series '55 Chevy 3600, 8 lug, 3/4 ton truck. I'm in the process of swapping out the front end to 6 lug and will soon be moving on to the rear end. The '55 is an open drive shaft. Do any of you know what 6 lug rear differential years with open drive shaft I can use on my '55?? Thank you all again!!

Joined: Mar 2010
Posts: 10,225
5
'Bolter
I would look for a '67 -'70 half ton truck rearend. They are 12 bolt with the correct 6 lugs and the width is very close to correct.

Joined: Oct 2019
Posts: 32
D
'Bolter
Thanks for letting me know about that 52Carl I didnt know that!

Joined: Jan 2000
Posts: 2,223
J
'Bolter
I used a 65-66 truck rear end on my 46, not to wide, lots of available ratios!


It's easier to get forgiveness than permission!
1946 1/2-Ton Chevy [stovebolt.com]
1953 Chevy 3/4-ton Factory Stakebed [stovebolt.com]
Joined: Oct 2019
Posts: 32
D
'Bolter
Originally Posted by JiMerit Boltr#43
I used a 65-66 truck rear end on my 46, not to wide, lots of available ratios!


Thanks JiMerit Boltr#43 and 52Carl. I'm very new with this driveline topic. If I end up getting a rear end from a '60s truck with the correct width do I have to worry about swapping out my transmission because of the gear ratio? I currently have the stock 235 engine and tranny. I assume the gear ratio from a later truck differential will be different than the the 4.56 gear ratio that came stock with my 3600. Also can I use my current drive shaft? Thank you very much for imparting your knowledge on this topic!

Joined: Mar 2010
Posts: 10,225
5
'Bolter
You might be able to use your current drive shaft. GM is famous for continuity throughout many years of production.

Joined: Oct 2019
Posts: 32
D
'Bolter
Ok got it 52Carl I'll let you know what I end up using..crossing my fingers the drive shaft will work with the new rear end. I'm glad I'm not restricted to the '55 1st series.

Last edited by D$TROYER; Sun Oct 20 2019 08:47 PM.
Joined: May 2015
Posts: 5,934
Housekeeping (Moderator) Making a Stovebolt Bed & Paint and Body Shop Forums
Shouldn't be an issue with the driveshaft. Worst case, it might need to be lengthened or shortened. If it's just a u-joint fit issue, u-joints with different size cups are available at any good driveline shop.


Kevin
Newest Project - 51 Chevy 3100 work truck. Photos [flickr.com]
#2 - '29 Ford pickup restored from the ground up.
First car '29 Ford Special Coupe
Busting rust since the mid-60's
Joined: Oct 2019
Posts: 32
D
'Bolter
Klhansen thanks for your input. Do you know if I have to worry about a transmission swap since the gear ratio will most likely be different?

Joined: May 2015
Posts: 5,934
Housekeeping (Moderator) Making a Stovebolt Bed & Paint and Body Shop Forums
Unless you're looking at an overdrive transmission, it won't make a difference. Most transmissions are direct drive in top gear.
Your rear axle ratio is 4.57 which is pretty low. Later axles are likely a higher ratio (eg.4.10, or even higher) which would help keep your highway cruising engine RPM down. Unless you're pulling stumps, you don't need a 4.57 rear axle ratio, although you could find an overdrive transmission, which would allow you to use a higher numerical ratio axle and still cruise down the highway at comfortable engine RPM's.


Kevin
Newest Project - 51 Chevy 3100 work truck. Photos [flickr.com]
#2 - '29 Ford pickup restored from the ground up.
First car '29 Ford Special Coupe
Busting rust since the mid-60's
Page 1 of 2 1 2

Moderated by  SWEET 

Link Copied to Clipboard
Home | FAQ | Gallery | Tech Tips | Events | Features | Search | Hoo-Ya Shop
Powered by UBB.threads™ PHP Forum Software 7.7.5