The Stovebolt Page Forums Home | FAQ | Forum | Swap Meet | Gallery | Tech Tips | Events | Features | Search | Hoo-Ya Shop
Work those trucks!




Share what you're up to this summer!

Stovebolt Site Search
 
Old Truck Calendars
Months of truck photos!
Nothing like an old truck calendar

Stovebolt Calendars

Check for details!


Who's Online Now
19 registered members (bowtietim, Bill Trotter, Bicounty, Brad Allen, cmayna, 1 invisible), 376 guests, and 2 spiders.
Key: Admin, Global Mod, Mod
Forum Statistics
Forums48
Topics116,264
Posts927,890
Members42,591
Most Online940
Apr 5th, 2017
Image Posting Policy
Previous Thread
Next Thread
Print Thread
Page 1 of 2 1 2
Ball Housing Collar #1314511 Sun Jun 16 2019 04:13 PM
Joined: Dec 2003
Posts: 3,933
S
Sedgewick Offline OP
Shop Shark
I have a persistent leak at the ball housing collar. I don't drive the truck much anymore and its easier for me to check the transmission oil and replace it if its low than to pull the ball housing apart to replace the seal. But it would be nice to not have oil drops on the floor.
When I bought my 53 the PO had apparently stuffed the collar with some sort of liquid gasket and it never leaked. Of course there may have been a seal in the collar as well. I was thinking of trying the same idea, just sliding the collar back and packing it with some Fel-Pro "make-a-gasket" material. Or even plumbers packing they use on faucet seats. I used the Fel-Pro product on my differential cover years ago and its not leaking.
I do know that its not the torque tube seal causing the leak because I did install an Okie assembly years ago and I always check my differential fluid to see if the trans oil is bypassing the seal.
Any ideas or comments.


"Sedgewick"
1949 Chevy 1/2-Ton
1989 Caprice

Re: Ball Housing Collar [Re: Sedgewick] #1314515 Sun Jun 16 2019 04:29 PM
Joined: Feb 2004
Posts: 19,186
H
Hotrod Lincoln Online
Boltergeist
I'd attach a big cookie sheet or a pizza pan to the floor with double stick tape and use a layer of newspaper or rags to catch the drips. Unless you're losing enough oil to nasty up the frame, sometimes it's simpler to deal with the drips than go to a lot of effort fixing a minor seep leak.
Jerry


The murder victim was drowned in a bathtub full of Rice Krispies and milk.
The coroner blamed the crime on a cereal killer!

Cringe and wail in fear, Eloi- - - - -we Morlocks are on the hunt!
Re: Ball Housing Collar [Re: Sedgewick] #1314518 Sun Jun 16 2019 04:49 PM
Joined: Apr 2008
Posts: 731
F
Forty9 Offline
Shop Shark
The collar was originally sealed using a thick cork gasket squeezed between 2 large washers. Doing that would naturally entail opening the ujoint ball, disassembling the u joint and dropping the torque tube to slide the parts on. The cork gasket is easy to find but the washers may be hard to find. There is a rubber O ring (National #327) that has been mentioned in these forums as a suitable substitute for the cork gasket that may work for the scenario you're thinking of trying. Cut the O ring, slip into place and use a bit of sealant where you cut it. Just a thought.


Ed
Re: Ball Housing Collar [Re: Sedgewick] #1314521 Sun Jun 16 2019 05:08 PM
Joined: Feb 2004
Posts: 19,186
H
Hotrod Lincoln Online
Boltergeist
We used to make our own O rings by using the correct diameter rubber cord and a dot of Super Glue to join the ends. The same process could be used on that torque tube nut seal if necessary to prevent having to dismantle everything. Square O ring material is also available instead of round stuff if you do a little internet searching or you have an industrial gasket and seal supplier in your area.
Jerry


The murder victim was drowned in a bathtub full of Rice Krispies and milk.
The coroner blamed the crime on a cereal killer!

Cringe and wail in fear, Eloi- - - - -we Morlocks are on the hunt!
Re: Ball Housing Collar [Re: Sedgewick] #1314527 Sun Jun 16 2019 06:13 PM
Joined: Dec 2003
Posts: 3,933
S
Sedgewick Offline OP
Shop Shark
I have both the cork and the rubber gaskets and at least 2 steel washers. The idea of cutting the gasket is something I never thought about and I like it. I guess I would have to cut one of the steel washers as well. The other could stay in place.
I have a spare ball housing and collar so I could use those as "Polish blueprints". I just do not want to dismantle the unit for as Jerry says, a few drops.
Thanks.


"Sedgewick"
1949 Chevy 1/2-Ton
1989 Caprice

Re: Ball Housing Collar [Re: Sedgewick] #1314528 Sun Jun 16 2019 06:34 PM
Joined: Feb 2004
Posts: 19,186
H
Hotrod Lincoln Online
Boltergeist
Since the gasket fits between the steel washers, why would you need to cut one of them? Just slide the nut and one of the washers back on the torque tube and put the cut gasket between the washers. I'd definitely look into using a nitrile O ring or something more durable than cork as an upgrade to the original gasket material. Super glue will also join cork, if you decide to stay with the original material. The cork can be made more pliable by steaming it or soaking in hot water before installing. That's a trick we used to use to reclaim dried-out cork valve cover gaskets from old gasket sets.
Jerry


The murder victim was drowned in a bathtub full of Rice Krispies and milk.
The coroner blamed the crime on a cereal killer!

Cringe and wail in fear, Eloi- - - - -we Morlocks are on the hunt!
Re: Ball Housing Collar [Re: Sedgewick] #1314530 Sun Jun 16 2019 06:54 PM
Joined: Dec 2003
Posts: 3,933
S
Sedgewick Offline OP
Shop Shark
I was thinking that as the collar won't slip off the torque tube and I have to cut the gasket to go around the TT then I would have to cut the steel washer - the rear most one. The one at the front end of the collar would not need to come off so I would leave it intact. And I do not know about the "nut". Maybe I am missing something here. Might see it differently once I have it apart.

I went through my gasket collection and found the Fel-Pro "Universal Joint Set" . Their number is ES72843. The kit consists 4 retainer shims, the rubber collars/packing for the join between the ball housing and the rear of the transmission and the threaded collar.


"Sedgewick"
1949 Chevy 1/2-Ton
1989 Caprice

Re: Ball Housing Collar [Re: Sedgewick] #1314535 Sun Jun 16 2019 07:39 PM
Joined: Feb 2004
Posts: 19,186
H
Hotrod Lincoln Online
Boltergeist
OK - - - -we're talking about a different seal. Back where the collar meets the tube there's a round threaded nut that squeezes a cork packing down against the torque tube to seal the lubricant as the tube slides in and out of the ball assembly. That's usually where the leak originates. Apparently you're talking about some type of larger diameter seal between the ball and the back of the transmission?
Jerry


The murder victim was drowned in a bathtub full of Rice Krispies and milk.
The coroner blamed the crime on a cereal killer!

Cringe and wail in fear, Eloi- - - - -we Morlocks are on the hunt!
Re: Ball Housing Collar [Re: Sedgewick] #1314542 Sun Jun 16 2019 09:06 PM
Joined: Dec 2003
Posts: 3,933
S
Sedgewick Offline OP
Shop Shark
No I was talking about the knurled collar at the rear end of the ball housing assembly. By a nut do you mean the threaded/knurled collar? That has the cork/rubber seal with a thin steel washer on either side of the seal and is threaded onto the ball housing. This is what I am talking about and I guess my initial posting did not specify exactly.


"Sedgewick"
1949 Chevy 1/2-Ton
1989 Caprice

Re: Ball Housing Collar [Re: Sedgewick] #1314544 Sun Jun 16 2019 09:39 PM
Joined: Feb 2004
Posts: 19,186
H
Hotrod Lincoln Online
Boltergeist
Just about anything with female threads is what I call a "nut".
Jerry


The murder victim was drowned in a bathtub full of Rice Krispies and milk.
The coroner blamed the crime on a cereal killer!

Cringe and wail in fear, Eloi- - - - -we Morlocks are on the hunt!
Page 1 of 2 1 2

Moderated by  SWEET 

Home | FAQ | Forum | Swap Meet | Gallery | Tech Tips | Events | Features | Search | Hoo-Ya Shop
Powered by UBB.threads™ PHP Forum Software 7.7.3