|
Share what you're up to this summer!
|
|
|
|
4 registered members (WE b OLD, Scott54, moparguy, 1 invisible),
336
guests, and 3
spiders. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
Forums48
Topics116,443
Posts926,239
Members42,439
| |
Most Online940
Apr 5th, 2017
|
|
|
 New head bolts for 261 needed
#1310389
Sat May 11 2019 05:44 PM
|
Joined: Aug 2015
Posts: 17
OP
New Guy
|
I need new head bolts for my 261
I have looked everywhere, to no avail..... Help !!!!
Whatever you are doing, have a good time at it..... Ya gotta do it anyway... So, enjoy life !!!!
|
|
|
|
Re: New head bolts for 261 needed
[Re: 60GMCFlat]
#1310391
Sat May 11 2019 06:10 PM
|
Joined: Feb 2004
Posts: 19,025
Boltergeist
|
Measure the length of the head bolts you need and go to either the Dorman or Pioneer open stock head bolt listings. They're simply 1/2"-13 Grade 8 head bolts, nothing fancy about them. You might consider using Grade 8 SAE flat washers under the bolt heads. Bolts for a 54-62 235 will work, also.
Jerry
The murder victim was drowned in a bathtub full of Rice Krispies and milk.
The coroner blamed the crime on a cereal killer!
Cringe and wail in fear, Eloi- - - - -we Morlocks are on the hunt!
|
|
|
|
Re: New head bolts for 261 needed
[Re: 60GMCFlat]
#1310395
Sat May 11 2019 06:14 PM
|
Joined: Nov 2011
Posts: 187
Shop Shark
|
Are they the same as 235 216 head bolts? I have many of them.
Trombones Totem Poles And Old Trucks!
|
|
|
|
Re: New head bolts for 261 needed
[Re: 60GMCFlat]
#1310413
Sat May 11 2019 09:55 PM
|
Joined: Sep 2001
Posts: 28,585
Boltergeist
|
Place a Parts Wanted Ad in the Swap Meet?
|
|
|
|
Re: New head bolts for 261 needed
[Re: '54 3600]
#1310867
Wed May 15 2019 11:55 PM
|
Joined: Aug 2015
Posts: 17
OP
New Guy
|
Hallelujah !!!!! WONDERFUL !!! Talked to them.... Made my day !!!!! THANK you, George.....
Thanks again,
Carl
Last edited by John Milliman; Thu May 16 2019 10:09 AM. Reason: Removed phone number
Whatever you are doing, have a good time at it..... Ya gotta do it anyway... So, enjoy life !!!!
|
|
|
|
Re: New head bolts for 261 needed
[Re: 60GMCFlat]
#1310879
Thu May 16 2019 01:36 AM
|
Joined: Aug 2015
Posts: 17
OP
New Guy
|
Hey George,
I have a set of head to block dowels coming... where do they go ?
I want to get this right...
Thanks,
Carl
Whatever you are doing, have a good time at it..... Ya gotta do it anyway... So, enjoy life !!!!
|
|
|
|
Re: New head bolts for 261 needed
[Re: 60GMCFlat]
#1310889
Thu May 16 2019 09:28 AM
|
Joined: Jul 2007
Posts: 495
Shop Shark
|
Carl , The two cylinder guide pins get screwed into the cylinder block Front & Rear holes on the manifold side of the engine . This holds the gasket in position so you can guide the cylinder head into place . You can do a trial fit when the block & head are super clean . Screw the guides thru the head gasket . You could go to the hardware store & buy a couple of carriage bolts - 1/2 " - 13 x 5 or 6 inches and cut the heads off to use as guides . PIC https://i.postimg.cc/FsPJfZVH/261-head.jpgGeorge '54 3600
1954 3600
|
|
|
|
Re: New head bolts for 261 needed
[Re: 60GMCFlat]
#1310890
Thu May 16 2019 10:12 AM
|
Joined: Nov 1995
Posts: 4,197
Founder/Developer
|
Carl -- I removed your phone number from your post -- that sort of Personally Identifiable Information is best left to PM's or email.
And by the way, have you read our Tech Tip on 261 rebuilding?
Thanks for using our site!
John
John
'49 Chevrolet 3804
|
|
|
|
Re: New head bolts for 261 needed
[Re: '54 3600]
#1310912
Thu May 16 2019 03:50 PM
|
Joined: Aug 2015
Posts: 17
OP
New Guy
|
|
Whatever you are doing, have a good time at it..... Ya gotta do it anyway... So, enjoy life !!!!
|
|
|
|
