The Stovebolt Page Forums Home | FAQ | Forum | Swap Meet | Gallery | Tech Tips | Events | Features | Search | Hoo-Ya Shop
Work those trucks!




Share what you're up to this summer!

Stovebolt Site Search
 
Old Truck Calendars
Months of truck photos!
Nothing like an old truck calendar

Stovebolt Calendars

Check for details!


Who's Online Now
7 registered members (DaveV, joronabell, marzach, Roy Rodgers, 2 invisible), 242 guests, and 3 spiders.
Key: Admin, Global Mod, Mod
Forum Statistics
Forums47
Topics114,670
Posts909,731
Members41,990
Most Online940
Apr 5th, 2017
Image Posting Policy
Previous Thread
Next Thread
Print Thread
Instrument cluster removal #1293181
Wed Jan 02 2019 12:39 AM
Wed Jan 02 2019 12:39 AM
F
fireguyfire  Offline OP
Wrench Fetcher
Joined: Aug 2018
Posts: 30
Southern Alberta
Stripping out the interior on my 41 fire truck, and I’m just about ready to remove the dash.
On these old chevs, can you bring the instrument cluster forward out of the dash, and then disconnect everything, or does it have to be done from underneath?
Any removal tips or tricks would be appreciated!

Re: Instrument cluster removal [Re: fireguyfire] #1293195
Wed Jan 02 2019 02:04 AM
Wed Jan 02 2019 02:04 AM
M
Mike B  Offline
Shop Shark
Joined: Mar 2004
Posts: 3,642
Hughesville, MD
You'll get more responses and views if you post your generic truck questions in the Big Bolt section and ask just the Fire Body/Equipment specific questions here in the Fire Bolt section.

Mike B smile

Re: Instrument cluster removal [Re: fireguyfire] #1293200
Wed Jan 02 2019 02:45 AM
Wed Jan 02 2019 02:45 AM
F
fireguyfire  Offline OP
Wrench Fetcher
Joined: Aug 2018
Posts: 30
Southern Alberta
Thanks for the tip Mike; makes sense.

Re: Instrument cluster removal [Re: fireguyfire] #1293201
Wed Jan 02 2019 02:49 AM
Wed Jan 02 2019 02:49 AM
H
Harold46  Offline
Shop Shark
Joined: Jul 2008
Posts: 1,152
Georgia
The cluster has to be removed from the rear. There are two nuts holding the unit to the dash, one on each side of the cluster frame.
Remove the speedometer cable, unplug the 3 light sockets (snap out), remove the gas gauge wire, remove the Amp meter wires, unscrew and remove the oil pressure line, disconnect the temp line from the motor (it does not separate from the gauge). Once everything is clear gently push the cluster into the dash and remove from the rear. The temp line has to come through the firewall so a helper would be good to have. Take caution with the temp line. If it breaks the whole unit will have to be replaced.

If you are doing a complete dash restoration you may want to remove the dash as a unit and then remove the cluster. Again watch out for the temp line.

In case you want to remove the dash, here are some suggestions.
The following bolts/screws hold the dash in place:
There are six clutch head 8-32 screws on the top dash lip underneath windshield. Remove two 5/16 bolts one each on the lower fronts (near the upper door hinge). Disconnect the windshield regulator, steering wheel brace and center dash brace. Tilt the dash out at the bottom and gently lift up as it has a lip that fits over the windshield area. It helps to remove the steering wheel (gives you more working room)

Good luck with your restoration.
Harold


Attached Files
Cab Interior (2).JPG (42 downloads)
Last edited by Harold46; Wed Jan 02 2019 03:08 AM. Reason: Add dash removal instructions

Harold
Is a restoration ever finished?
Re: Instrument cluster removal [Re: fireguyfire] #1293353
Thu Jan 03 2019 01:17 PM
Thu Jan 03 2019 01:17 PM
F
fireguyfire  Offline OP
Wrench Fetcher
Joined: Aug 2018
Posts: 30
Southern Alberta
Fantastic information; thanks Harold!


Home | FAQ | Forum | Swap Meet | Gallery | Tech Tips | Events | Features | Search | Hoo-Ya Shop
Powered by UBB.threads™ PHP Forum Software 7.6.1.1